Blue Label OBD Bluetooth ELM327 car fault diagnosis Scan Tool ELM327 OBD2 v1.5

ELM327 is the latest PC-based OBD2 Universal Car diagnostic test tools. It supports all OBD-II self-diagnostic system and its compatible communication protocol detection. ELM327 USB interface to connect a laptop via RS232 interface to USB transfer protocol.
Support OBD-II on-board diagnostics protocols:
..ISO15765-4 (CAN)
..ISO14230-4 (KWP2000)
..ISO9141-2
..J1850VPW
..J1850PWM
Output protocol mode: RS232
Baud rate: 9600 or 38400
LED indicator: OBDTx / Rx, RS232Tx, power
Operating voltage: 12v
Operating Current: 45mA
Features:
ELM327 USBOBD-II self-diagnostic system using free software program that allows you to use your PC and get your car engine ELM327 various computer data. Software is simple to learn. The software supports DOS and Windows computer operating system.
Features:
1. Read General & car manufacturer-specific diagnostic fault codes, and display their definitions (containing more than 3,000 software fault code)
2. Clear trouble codes and turn off the engine (engine) failure alarm indicator
3. Read instant dynamic data flow engine
..Engine speed
.. Calculated load value
Coolant temperature ..
.. Fuel System Status
Speed ..
Short-term fuel trim ..
Long-term fuel correction ..
.. The intake manifold pressure
.. Timing advance
Intake air temperature ..
..air flow
.. Throttle opening
.. Oxygen sensor voltage / short-term fuel trim
.. Fuel pressure. . . .
Supported models:
Ford Jaguar Mercedes MINI BMW SEAT VW
Acura Chrysler Dodge BYD F3 / F0 Chery 09 Alto
Toyota, Nissan, Mazda, Honda Suzuki Mitsubishi Subaru
Land Rover Infiniti Kia Skoda Modern Chevrolet
Saab Opel Audi Peugeot Citroen and Fiat Volvo
Installation and use instructions
LM327 automotive diagnostic equipment installation and use instructions
Vehicle fault codes
Automotive Diagnosis
This product is manufactured after 1996 support using OBD-Ⅱ protocol models (including the VPW, PWM, ISO, KWP 2000, CAN protocol). The product can connect to a laptop or desktop computer for reading fault code and know the meaning of fault codes, clear fault codes car, display current sensor data (such as speed, temperature, etc.) ...... very powerful!
Features:
The product supports all OBD-Ⅱ protocol, output USB interface, more convenient to connect to the laptop.
Product Features:
OBD-Ⅱ agreement: ISO15765-4 (CAN)
ISO14230-4 (KWP2000)
ISO9141-2
J1850 VPW
J1850 PWM
Output Interface: USB
LED indicator: OBD transmitter / receiver, RS232 transmitter / receiver, power supply
Operating voltage: 12V, (with short circuit / over-voltage protection)
Product Features:
Read the fault code and know the meaning of fault codes, clear fault codes car, display sensor data (including: engine speed, coolant temperature, vehicle speed, intake manifold pressure, intake air temperature, air flow, throttle position , oxygen sensor voltage, fuel pressure, etc.) as well as other more advanced features ......
Graphics interface software commonly used are: Scantool, Scanmaster, Proscan, PcmSCAN, Digimoto, you can also use AT commands to use with the Super Terminal.
Installation instructions :( Tips If you can not read the software installation CD inside, please download the software from the link below :)
1, the vehicle information reading software ScanTool (dot) net:
2, USB drivers:
installation steps:
1, the installation CD or downloaded ScanTool (dot) net software.
2, the OBD-Ⅱ cables and car ODB-Ⅱ interface.
3, OBD-Ⅱ cable ELM327 connection. At this time, the power light (power) lights, ODB TX / RX light flashes, indicating that the connection is normal.
4. Connect the USB cable to connect ELM327 computer. At this point the computer will prompt the discovery of new hardware, follow the computer prompts within an installation CD or network to download the USB drivers. Into the computer's "Device Manager" Click the port, you will find the newly installed hardware "USB Serial Port", a note on the right COM number. (The COM number will be used in the next software settings)
5, start ScanTool (dot) net software. Open ScanTool (dot) netv1.13 for windows program, select options (Settings) items, you select the COM number in the previous step you down, and then OK. Such software installation is complete, you can diagnose your vehicle up