Contact Platform Support
Help CenterHydrostatic Test Machine for Seamless Gas Cylinder
Related Products
-
Hydraulic Volumtric Expansion Test Machine for Gas CylinderUS$ 0.1 - 0.9MOQ: 1 Set -
DW-01 Gas Cylinder Test Equipment for Gas CylinderUS$ 100 - 3,000MOQ: 1 Piece
-
SY-02 Hydrostatic Test Machine for Seamless Gas Cylinder Test EquipmentUS$ 100 - 3,000MOQ: 1 Piece
-
PFX-01 Hydrostatic Test for Seamless Gas Cylinder Test EquipmentUS$ 100 - 3,000MOQ: 1 Piece
-
CX01 Shot Blasting Rust Remover EquipmentUS$ 100 - 3,000MOQ: 1 Piece
Specifications
Hydrostatic Testing for seamless gas cylinderWith two water jackets
Certificate: ISO9001
Standard: GB/T9251, ISO6406
SY-02 Hydrostatic Test Machine is used for water jacket method hydrostatic testing for all kinds of gas cylinders during their manufacturing, inspection and evaluation. The test machine is designed and manufactured according to GB/T9251-1997 Hydrostatic Testing Method for Gas Cylinderand American DOT standard.
Main technical parameter:
Pump model |
GD80 |
Max. outlet pressure |
64Mpa |
Electronic balance |
0-1500g (accuracy 0.1g) |
Pressure sensor |
0-70Mpa (accuracy 0.1g) |
Test pressure |
≤40Mpa |
Air pressure |
0.3-0.8Mpa |
Work power |
AC220V/50HZ |
Control mode |
PC/Manual |
Applicable medium |
Water |
Flow |
3.96L/Min |
The test machine is suitable for cylinders as below:
Capacity: up to 130L; Length: from 90cm to 200cm
Diameter: from 110mm to 410mm
Application:
Hydraulic volumetric expansion testing for CNG cylinder, LPG cylinder, fire extinguishers, seamless cylinder, breathing cylinder, pressure accumulator, steel cylinder, (Direct volumetric expansion testing and water jacket testing are available)
The machine is mainly used for cylinder pressure test and achievement of gas cylinder volume residual deformation rate.
Key features and advantages:
- Control mode: PC control
- Software specification and display ((include: pressure rate, drop pressure detection, show test time, save data for each cylinder, P-T diagram for each cylinder from beginning to end of the test).
- Real-time monitoring as well as data recorded on high-speed sampling cards and also testing curves printing
- Alarming at due time bursting and due point recording
- A variety of tooling and fixtures meeting with different mounting method requirements
- Non-welded pipeline system
- Industrial control configuration software on LABVIEW
Working principle:
Put the cylinder into a water jacket and boost the cylinder by high pressure pump. It will automatically dwell at set pressure and do pressure test on the cylinder. At the same time, the cylinder valume expands under test pressure and squeezed some water from water jacket into the measuring cup, and it is test cylinder volume deformation. The water is transferred to PC by water collection system, the elastic deformation disappears after cylinder relief of pressure, then the water flows back from measuring cup to water jacket.However, the remainning water in the measuring cup is still more than that before boosting the cylinder. The extra water volume is the test gas cylinder volume residual deformation. While the gas cylinder volume residual deformation rate is the ratio of the test gas cylinder volume residual deformation to all deformation.
Note:
ing pressure: 40Mpa,
The actual test pressure control accuracy:no less than 10 psig
The actual water level measurement accuracy: no less than 0.4.
Send Inquiry to This Supplier
You May Also Like
-
Endress+Hauser E+H Compact Conductivity Device Smartec CLD18-BGGENegotiableMOQ: 1 Piece
-
Laser Shaft Alignment Tool Heat Press Laser AlignmentNegotiableMOQ: 100 Pieces
-
Technical Single Column Computerized Bending Testing Machine Single Column Computerized Universal Testing MachineUS$ 4500 - 10000MOQ: 1 Set
-
OMP60 Renishaw Probe A-4038-0001-21 A-4038-0002 Original and NewNegotiableMOQ: 1 Piece
-
Shaft Alignment Tool SKF TKSA 31 Laser Alignment Tool Shaft AlignmentNegotiableMOQ: 100 Pieces
-
SKF TKSA 31 Basic Wired Laser Shaft Alignment ToolNegotiableMOQ: 100 Pieces
-
High Quality Shaft Alignment Tool Tksa31 With Good Price, Laser Alignment, Tksa SeriesNegotiableMOQ: 100 Pieces
-
Shaft Alignment Tool TKSA 51 Large Sized Detectors and Powerful Lasers,quickly Check and Correct Shaft Alignments,very Easy to UseNegotiableMOQ: 100 Pieces
-
SKF TKSA 31 Laser Axis Intermediate Tool Easy-to-Use Touch Screen Quick Customization OEM Support Test Instruments ProductNegotiableMOQ: 100 Pieces
-
TKSA 51 Shaft Laser Aligner Alignment Tool High Quality With Good PriceNegotiableMOQ: 100 Pieces
