G APP Modified Bitumen Membrane
APP modified bitumen membrane is made by saturating the base in bitumen, or thermoplastics (such as APP,APAO,APO), then covering double faces with thermoplastic elastomer (SBS) and last finishing the upward face with fine sands, mineral slates(or grains) or polythene membrane etc. while downward face with fine sands or polythene membrane.
Characteristic
APP modified bitumen membrane is applied in the hot area with high temperature. Good performance in anti-puncture, anti-broker, anti-resistance, anti-erosion, anti-mildew, anti-weathering. Construction is convenient, the melt method can operate in four seasons, joints are reliable
Specification:
Item |
Type |
PY Polyester G Glassfibre PYG Glassfibre enhance polyester felt PE PE Film S Sand M Mineral |
||||||
Grade |
Ⅰ |
Ⅱ |
||||||
Reinforcement |
PY |
G |
PYG |
|||||
Surface |
PE |
San |
Mineral |
|||||
Thickness |
2mm |
3mm |
4mm |
5mm |
||||
With |
1000mm |
|||||||
Applicable scope
Suitable for civil building roofing, underground, bridge, parking, pool, tunnel in the line of waterproofing and damp proof, especially for the building under high temperature. According the roofing engineering stipulation, APP modified bitumen membrane could be used in the Grade civil building and industrial building which has special waterproofing requirement.
Storage and transportation instructions
A,When storage and transportation, Different types and sizes of products shall be stacking separately, should not be mixed. Storage temperature should not be above 50°C, the height is not more than two layers, in the course of transportation, membrane must stand.
B,The stacking height is not more than two layers. To prevent the tilt or pressure, when necessary cover the felt fabric.
C,In normal conditions of storage and transportation, storage period is a year since the date of production
No. |
Item |
Ⅰ |
Ⅱ |
||||||||||||
PY |
G |
PY |
G |
PYG |
|||||||||||
1 |
Soluble content/(g/m²)≥ |
3cm |
2100 |
* |
|||||||||||
4cm |
2900 |
* |
|||||||||||||
5cm |
3500 |
||||||||||||||
Test |
* |
No flame |
* |
No flame |
* |
||||||||||
2 |
Heat resistance |
℃ |
110 |
130 |
|||||||||||
≤mm |
2 |
||||||||||||||
Test |
No flow, no dripping |
||||||||||||||
3 |
Low temperature flexibility/℃ |
-7 |
-15 |
||||||||||||
No crack | |||||||||||||||
4 |
Impermeability 30 minutes |
0.3MPa |
0.2MPa |
0.3MPa |
|||||||||||
5 |
Tension |
Maximum/(N/50mm) ≥ |
500 |
350 |
800 |
500 |
900 |
||||||||
Secondly-Maximum |
* |
* |
* |
* |
800 |
||||||||||
Test |
No crack, no apart |
||||||||||||||
6 |
Elongation |
Maximum/%≥ |
30 |
* |
40 |
* |
* |
||||||||
Secondly-Maximum≥ |
* |
* |
15 |
||||||||||||
Send Inquiry to This Supplier
You May Also Like
-
2.0mm Textured HDPE Geomembrane Dual-Sided Friction for Slope ProtectionUS$ 9.5 - 10MOQ: 100 Square Meters
-
High Adhesive, Water-proof, Anti Corrosion, Weather-resistant Asphalt Adhesive Glue Patch Cover for ConstructionNegotiableMOQ: 100 Rolls
-
GeomembraneNegotiableMOQ: 2700 Rolls
-
Non-curable Rubber Paint Rubber Asphalt Waterproof Coating Made in ChinaUS$ 1.5 - 6MOQ: 500 Kilograms
-
Low Cost Waterproof Material ManufactureUS$ 1,000 - 50,000MOQ: 1 Set
-
PTFE Architectural Membrane MaterialNegotiableMOQ: 1
-
Special Compound BaseUS$ 0.12 - 0.25MOQ: 7000 Square Meters
-
PolyLock/HDPE Lock/ E Lock/ HDPE E Lock/Geomembrane Attaches HDPE GeomembranesUS$ 10 - 50MOQ: 1 Piece
-
Breathable House Wrap Membrane Roofing Waterproofing MembraneUS$ 0.42 - 0.42MOQ: 5000 Square Meters
-
<MIicroVENT> Waterproof Vent MembraneUS$ 0.1 - 3MOQ: 10000 Pieces