144W DMX LED Wall Wahser

Specifications

144W LED Stage light
1.144x1W led, RGB full color
2.DMX512 control
3.Over 50,000 hours
4.CE&RoHS certificate

 

144W RGB LED WALL WASHER, DMX LED WALL WASHER

 

 

 

 

 

SPECIFICATION

 

 

 

Model No.	LED Quantity	Color	Opreating Current	Power Consumption	Beam Angel	Project distance
BG-806-144W	144X1W	R-48, G-48, B-48	10.5A (Max.)	160Watts	15°30º 45º 60°90°	35-50M

 

WORKING TEMPERATURE

 

Environment temperature	-20°C ~ +45°C
IP Rank	IP65

 

CONNECTION PORTS

 

1. Light Body part:
   1) One pc 24VDC power supply input terminal: 2-pin male waterproof connector(connect with the 2-pin female connector of power supply)
   2) One pc standard DMX signal input terminal:  3-pin male connector(connect with the 3-pin female connector of controller part)
2. Power supply and controller parts:
   1) One pc high voltage input terminal: 3-pin bare wire
    2) One pc 24VDC power supply output terminal: 2-pin waterproof female connector
    3) One pc standard DMX signal input terminal: 3-pin male waterproof connector(light signal input use)
   4) One pc standard DMX signal output terminal: 3-pin female waterproof connector (connect with next light)
   5) One pc standard DMX signal output terminal: 3-pin female waterproof connector ( connected with the three-pin male connector of light body ,signal output to light body )
3. Dimension diagram
   1. "L1" stands for the whole length of wall washer
   0.6 m wall washer:L1=614mm
   
   2. 'L2" stands for the length between the middle of two location brackets
   0.6 m wall washer:L1=512 mm

 

 

 

 

1. 
   Diagram for installation and connection
   1. Single color wall washer, can be lighted up with power on
   2. The connection way of RGB colors, as follows:

 

 

 

 

 

 Attention:
1. Please consider about "the working condition", the lamp can not be put in water for long time

2. Each 0.6m RGB wall washer takes up 6 DMX addresses, the former wall washer's address plus 6 is the address for the next one.

 

3. If you want all connected wall washers to change colors together, you should set the same address for all the washers.

4. Please set the address from smaller to bigger.

5. The maximum address of RGB wall washer should be less than 510.

6. There should be only one main flood light as a master (the flood light works in main control mode, control box or control console).

7. When there are many  wall washer  connected together, the connections please refer to the connection diagram.

8. The connection cable between two controllers, or between console and signal amplifiers. It can't exceed 100m; The distance between the first signals amplifier or console and the last flood light can't exceed 100m.

 

Instruction for installation
1. The wire of power supply and signal of last wall washer of each loop should be used tail plug for waterproof

2. Please make sure there is no short circuit before turn on the power, otherwise the parts of the device would be burn out.

3. Around the lamp should fill with some gravel or sand when installation, it is better for the heat rink and drainage. And make sure there is no corrosive, inflammability and explosive material around.
Note: A. Make sure the power is be turned off while installation or dismounting.
B. Please replace with new lamp when the lamp body is defected.

 

 

 

Problems and solutions:
1. If the light cannot light up, please check whether it connects with power supply well and whether the switch is on.
2. If the light turns on and off frequently, please check whether the connection between power and lamp is fixed enough.
Note: Please contact professionals in case of above solutions do not work; please try to contact professionals instead of open the light at once.