Contact Platform Support
Help CenterConventional Infrared Beam Smoke Detector
Related Products
-
Conventional 12V Photoelectric Fire Smoke DetectorNegotiableMOQ: 300 Pieces -
2-point Conventional Photoelectric Optical Smoke DetectorNegotiableMOQ: 300 Pieces
-
4-Wire Conventional 2-Point Photoelectric Smoke DetectorNegotiableMOQ: 500 Pieces
-
Conventional Photoelectric Optical Smoke DetectorNegotiableMOQ: 500 Pieces
-
Infrared Beam Smoke DetectorNegotiableMOQ: 1
Specifications
1. Weight: 0.6kg2. Dimensions: 65x65x110 mm
3. D.C. voltage: 10-30 V
4. Monitored distance: 10-100 m
5. Connection: 2 wire
Conventional Infrared Beam Smoke Detector consists of 2 units
Features:
- Application: large premises including ones with original configuration of ceilings (churches,theatres, museums)
- Intellectual microprocessor data processing provides better and earlier detection of different types of fires, including “black smoke” and eliminates false alarms
- 2 units: receiver and transmitter in the same housings placed on the opposite sides of the protected area
- Indication: two red LEDs on both units indicating standby mode and faults
- Attaching: angle and arc brackets (also used to mechanically adjust the detector)
- Metal cases: provide additional false alarm immunity
- RANGE and CALIBRATION switches on the rear side of the receiver
- 2 attenuators used to adjust and check sensitivity
- Wiring: 2-wire, 4-wire through the MUSH-DL module
1 PURPOSE
1.1 The detector is designed to detect smoky fires inside large premises.
1.2 Detector consists of 2 units: transmitter (Tx) and receiver (Rx). Tx and Rx are connected to each other and to alarm loop through external interface units (EIU-1).
1.3 The detector transmits the Fire and the Fault messages. The detector transmits the Fire message when infrared radiation flux between Tx and Rx is slackened by smoke in specified number of times, and the Fault message when the infrared radiation flux is completely obscured or electrical connection between units is broken. These messages are indicated with red LED indicators on the receiver.
1.4 The Fire outcoming signal retains after combustion aerosol products affecting is over. You can reset the detector to standby mode switching off the mains supply for at least 5 s.
1.5 The detector is designed for continuous-running operation with 24V DC FACP.
2 TECHNICAL SPECIFICATIONS
2.1 Detection range: 10 ÷ 100 m
2.2 D.C. voltage range: 10 ÷ 30 V
2.3 Tx current consumption in standby mode: 1 mA
2.4 Rx current consumption in standby mode: 1 mA
2.5 Rx current consumption in fire mode: 8+1,6 mA
2.6 Rx current consumption in fault mode: 25+5 mA
2.7 Rx voltage drop in fire or fault mode: 8 V
2.8 Tx voltage drop in standby mode: 8 V
2.9 Start-up time: 10 s
2.10 Dimensions of the detector’s units (w/o brackets): 67100 mm
2.11 Weight: 0,6 kg
2.12 Permissible angles of mechanical adjustment in horizontal plane: ±90 °
Permissible angles of mechanical adjustment in vertical plane: ±45°
2.13 Operating temperature range: from – 10 to 55 °
Relative humidity 95%
2.14 Operating temperature range: from -30° and lower (without moisture condensation)
2.15 Average lifetime: 10 years
Send Inquiry to This Supplier
You May Also Like
-
Fire Smoke SensorNegotiableMOQ: 2400 Pieces
-
CO DetectorNegotiableMOQ: 1 Piece
-
2015 High Quality Cheap Electronics Fire Alarm SirenUS$ 0.1 - 10MOQ: 5000 Pieces
-
2012 Newest Smoke Alarm/Detector/SensorUS$ 0.1 - 0.2MOQ: 200 Pieces
-
Fire Detection & SuppressionNegotiableMOQ: 1
-
TAKEX Flame DetectorNegotiableMOQ: 1 Piece
-
Addressable Photoelectric Smoke Detector Intelligent Smoke Sensor LPCB CE ApprovedNegotiableMOQ: 1 Piece
-
2025 China DC 48V Wired Smoke Detector With Relay Output For Electronics Panel SecurityNegotiableMOQ: 1080 Pieces
-
Wholers Sell KF94/N95/KN95/surgical Mask/KIDS Face Masks/adult Face Masks/kids Face Masks（SKYPE:lifuli123）US$ 0.5 - 1MOQ: 1 Piece
-
Wireless Sounder Strobe Wireless Fire Alarm Sound Flashing Lighting AlarmNegotiableMOQ: 1 Piece
