YRTM460 Rotary Table Bearing with integrated angular measuring system|turret bearing

YRTM460 Rotary Table Bearing with integrated angular measuring system|turret bearing|with integrated angular measuring system

YRTM rotary table bearings : Detailed parameter of YRTM rotary table bearings.

Axial/radial bearings YRTM, double direction, screw mounting, with integrated angular measuring system

     YRTM460 rotary table bearing consist of a thrust/radial housing washer, a thrust/radial shaft washer, a thrust washer, two Axial needle roller and cage assemblies and a group of radial cylindrical roller . The Housing washer and shaft washer have equally spaced fitting bolt. This kind of bearings( YRTM460)can support high axial load and radial load ,and it also have high tilting rigidity and high precision. YRTM460 rotary table bearing is based on the YRT460 rotary table bearings, it is mounted with magnetic angle measuring system, in order to accurately measure and adjust the angle of the bearing rotating and make sure the high rotation speeds.The Measuring system is composed of transmission chain and measuring scale. It adopts pure inductive measurement principle, so the signal,and the precision of measuring is very high. YRTM3460 can work reliably without too much maintenance; the application scope is very wide. It can be applied to high precision rotary table and axis rotation, index head, military radar, aviation, aerospace and the field with the high accuracy of Angle rotation in the measuring and the Test equipment. 

 YRTM rotary table bearing

High precision YRT rotary table bearings, YRT series ,YRTS series ,YRTM series, ZKLDF series.The precision rate has reached P5/P4/P2,ranging from 50mm --- 1300mm

Design & Installation for YRTM460:

Structure with the requirements shown in Figure 1

Retaining screws secure the bearing components during transport. For installing the bearing easier, the screws should be loosened before fitting, and secured again or replaced by positioning screws after fitting.

The L-section ring can be fitted with unsupported or supported ring.

a)  Without supported ring, the bearing type is YRT.

b)  With supported ring, the bearing type is YRT-VSP.And the whole surface of L-section should be supported.

Mounting forces must only be applied to the YRTM460 rotary table bearing ring to be fitted, never through the rolling elements.

Tighten the fixing screws in crosswise using a torque wrench (shown in figure 2).

Don’t separate or interchanged bearing components during fitting and dismantling. 

Starting friction torque can be 3 to 3.5 times as high as the value of friction torque in the dimension tables.

YRTM rotary table bearings are greased by a lithium complex soap grease and can be lubricated via the outer ring and L-section ring.

Limiting speeds:The bearings allow the limiting speeds given in the dimension tables. The operating temperatures occurring are heavily dependent on the environmental conditions. Calculation is possible by means of a thermal balance analysis based on frictional torque data.

Bearing preload:Once the bearings have been fitted and fully screw mounted,they are radially and axially clearance-free and preloaded.

Temperature differences:Temperature differences between the shaft and housing influence the radial bearing preload and thus the operating behaviour of the bearing arrangement. If the shaft temperature is higher than the housing temperature,
the radial preload will increase proportionally, so there will be an increase in the rolling element load, bearing friction and bearing temperature.If the shaft temperature is lower than the housing temperature,the radial preload will decrease proportionally, so the rigidity will decrease to bearing clearance and wear will increase.

Summary of YRTM:

----Magnetic measuring system

----Insensitive to contamination

----Easy access to rotary table surface (electricity / hydraulic power / air)

----Design envelope identical to YRT

----Easy to fit and set up due to adjustment and diagnostic software

Measuring System

The MEKO measuring unit is easy to access and replace;

Structure of dimensional scale:distance encoding every 15°;incremental signal 1 Volt ss;

Bearing size / accuracy:

YRTM 150 / ± 5"

YRTM 180 / ± 5"

YRTM 200 / ± 3"

YRTM 260 / ± 3"

YRTM 325 / ± 3"

YRTM 395 / ± 3"

1. Industrial Neutral Packing,Package as your requirements.

2. Small size Bearings:Plastic vacuum packaging bag+Paper Box/Neutral Carton

3.Large size Bearings:Plastic film+Brown paper+Roll tape+Wooden Box

4.Shipping:By air or By sea:DHL/TNT/UPS/EMS etc

2.Well-trained & experienced staff are to answer all your inquiries in English of course. 

3.OEM & ODM projects are highly welcomed. We have strong R&D team here to help. 

4.Your business relationship with us will be confidential to any third party. 

5.Good after-sale service offered, please get back if you got question

6.Nowadays, as a professional precision bearing manufacture, we are proud of continual innovation, flexible production, speedy delivery, rapid after-sales service(2 years) and quick response.

       Luoyang BoYing Bearing Co., Ltd, (BYC) is a professional manufacturer of high precision bearings,The main products  are Crossed roller bearings ,  YRT Rotary Table Bearings ,  Crossed Tapered Roller Bearings ,  Cylindrical Thrust Roller Bearing ,  Angular Contact Ball Bearings ,  Thin Section Bearings,Slewing Bearings  ,  Ball Screw Bearings . The accuracy grades are P5, P4, P2, and the size of inner ring are ranging from Φ50mm --- Φ1300mm. Our products are optimal for Robotics, Machine Tools, Rotary Table, medical equipment, measuring instruments ,mainly to replace the imported bearings. Also, we can design,choose and manufacture non-standard precision bearings as customer requested.

Tel: +86-379-62275175

SKYPE: lyboying

Email: lyboying@

Aliexpress: /store/1332007

http://bycbearing.en.china.cn  

MP: +86-15515365379