Home > Products > Porcelain Insulator > GOOD Quality Composite Lightning Protection Pin Insulator
GOOD Quality Composite Lightning Protection Pin Insulator
- 50000 Piece / Pieces per Month
- Fuzhou
- T/T Credit Card
Product Details
Place of Origin: | Fujian, China | Brand Name: | JUNXIN | Model Number: | FPEG-12(c)/5 |
Product Description
Product details:
I. With the development and distribution lines insulated line transformation of the traditional design, since the insulation resistance line has inherent level of mine , bear a direct role thunder or lightning , lightning break, porcelain insulators , have already become a power bombed another face a new problem. FEG -type lightning Insulator is a new modular structure of combo products , take the first blockage dredge design , enhanced insulation and anti- contamination level, suitable for overhead line insulation support, but also has to prevent lightning overhead insulated wires break, blow up and reduction of porcelain insulators lightning trip protection. The principle is : When the voltage exceeds the insulation plug lightning over a certain value, the lightning rod and steel pillars arc flashover between the legs caused by discharge , short-circuit channel , successive frequency arc discharge gap will be combusted in order to protect the wire from burns. This product is used insulated wire is energized with a puncture Shihai function , without peel core insulating layer can avoid water and corrosion, installation and construction is extremely convenient and reliable. Since the post insulator and arc-proof fittings combined ( equipotential ) , without ring network power supply load side ( departure from the power supply side ) effects , more so simple and beautiful lines and greatly reduce the cost . The products are reliable , less investment , the effect is large , for the electricity sector to prevent lightning overhead insulated wire breakage provides a cost-effective way .
II. Specifications and Performance Parameters
Model Specification | Insulated conductor cross-section mm2 | Lightning impulse withstand voltage ( peak ) KV | 1min power frequency withstand voltage ( RMS ) KV
Dry Wet | Frequency arc current ( rms ) KA | Rated withstand bending load KN | Minimum nominal creepage distance mm | Remark |
FPEG-12/5 | 50 /300 | 75 | 50 42 | 12.5 | 5 | 400 | Piercing |
FPEG-12C / 5 | 50 /300 | 75 | 50 42 | 12.5 | 5 | 400 | Non Piercing |
III. The structural characteristics
1) This product sub- piercing and non- piercing ( stripping insulation layer ) two kinds , the main by the insulation shield , clamp aluminum fittings , composite insulators, arc steel rod and the lower legs and other components.
2) Arc rod and clamp fittings assembled integrally connected , when lightning occurs, the arc between the legs of steel rods and caused flashover discharge , the formation of short -channel , successive frequency arc moves to the arc rods and steel feet between burning to protect the wires from burns. Stick arc bypass due to an optimal sheds and discharge gap , discharge and prevent burn better insulator sheds .
3) FEG-12/5 type with a puncture -type stab teeth structure , barbed teeth removable , skinning or skinning purposes optional . Barbed teeth using higher strength than aluminum and better electrical properties of the copper alloy , the surface through electrical ( infiltration ) with copper and aluminum plating process to prevent the oxidation , so that the line can be used as copper or aluminum . Piercing style without stripping wire insulation , avoiding core water and corrosion, installation and construction is extremely convenient, can greatly reduce the operator labor intensity .
4) Using composite materials than the PS-15 insulator porcelain insulators and other electrical insulating properties , and the creepage distance , improved anti- insulator contamination levels , which can meet the majority of users on the insulator contamination prevention requirements.
5) Insulation shield with silicone rubber material , has good insulation properties , anti-aging properties and flame retardance .
6) Has been taken into account to prevent birds from overhead wires causing a short circuit on the unique structure of harm .
7) Can tolerate about 5 times the frequency high- current arc burning .
IV. The installation method
1) Before installing the product , first check FPEG-12/5 pillars of high-voltage line lightning rod composite insulators and conductive arc voltage electrode assembly is securely connected into one , fastening nut of the high voltage electrode arc guiding rod and adjust to the desired position to ensure that the discharge gap against the direction and size.
2) Lightning Insulator clip trunking should be aligned parallel to the direction of conductors mounted on the cross arm , tighten the nut steel legs , equivalent to conventional insulators installation method, the arc rod toward the cross arm ( cross arm farthest distance ) away outside ; arc rod one direction , preferably towards the load side .
3) Puncture -type clamp way: according to wire section and weather temperature set torque wrench torque value :26-32Nm, alternately using a torque wrench , tighten the two symmetrical pressure nuts. Inspection with the naked eye , you can see the basic thorn tooth root , and then tighten the nut prepared to prevent the pressure nut loose . ( Trillion
4) Non- puncture -type clamp way: insulated wire peel of an approximately 65-80mm embedded insulator clamp fittings on the compression nut with a wrench to tighten the seat clamp wire can be driven by briquetting ; insulation shield mounted on the clip external line fittings .
V. Conditions of Use
1, Ambient temperature : -40 °C ~ 50 °C
2, The altitude does not exceed : 1500m altitude
3, The maximum wind speed : 35m / s
4 , The earthquake intensity : 8
VI. The Reference Standard
GB/T20142-2006 nominal voltage greater than 1000V AC overhead line post composite insulator - Definitions, test methods and acceptance criteria
JB/T8177-1999 insulator layer of galvanized metal accessories General technical requirements
GB311.1-1997 high-voltage power transmission equipment, insulation coordination
GB/T775.1/2006 insulators experimental methods General test methods - Part 1
GB/T775. 2/2003 Insulator Electrical test methods - Test methods - Part 2
GB/T775.3/2006 insulators experimental methods Mechanical test methods - Part 3
JB/T9673-1999 insulators
Other insulators
Contact Us
- Fujian Minqing Junxin Electrical Appliance Co., Ltd.
- Contact nameEmily Chow
- Phone0086-0591-86390653
- AddressDingkeng Village, Chiyuan Town, Minqing County Fuzhou,Fujian
- monopole steel tower
- power transmission line steel tower
- Electrical equipment frequency converter
- Vector Frequencyinverter
- Overhead power line fault indicator with Three color light display
- short circuit and earth fault indicator distribution system
- Current Temperature And Faults On-line Monitoring instrument
- how to reset overhead line earth fault indicator
- Electric Power Overhead type Cable Fault Indicator
- Simulated Failure Remote Controller for Overhead Line Fault Indicator
- Flag type Overhead type Short circuit &Ground Fault Indicator
- Installation adapter of Overhead Line Fault Indicator
- short circuit and earth fault passage indicator with good price
- overhead Line fault indicator for installation methods and tools
- Flag type Overhead type Short circuit &Ground Fault Indicator
- High Voltage Cable Fault Alarm
- overhead line fault sensor
- SNV-QS High Voltage Live Display Locking Device
- EKL4 Cable Short Circuit and Grounding Fault Indicator
- EKL4 Cable Short Circuit and Grounding Fault Indicator
- Remote Wireless Communication Terminal for overhead grounding and short circuit fault
- medium voltage overhead line fault current sensor and indicator
- Overhead type Short circuit & earth Fault Indicator manufacturer
- earth fault indicator distribution system
Popular Searches
Recommended Products
- BENTLY 1900/65A-00-04-01-00-00 Device monitor
- ABB XVC768101 3BHB007211R101 power interface Module
- ABB LD800HSE communication interface module
- ABB UAC389AE02 HIEE300888R0002 Excitation control module
- ABB UAC383AE01 HIEE300890R0001 Control board
- ABB PPC907BE101 3BHE024577R0101 frequency converter
- GE ESP10B Flow and pressure controller
- GE ESM10A Ethernet communication module
- ABB DSAO120A 3BSE018293R1 Excitation conditioning
- ABB KSD211B 3BHE022455R1101 Coupling device unit
- HONEYWELL 05701-A-0302 Single channel control card
- ABB XVC768115 3BHB007211R115 Remote IO devices
Find Similar Products By Category
- Electrical Equipment & Supplies > Power Distribution Equipment
- Buy on GoldSupplier.com
- How to Buy
- Browse by Catagories
- Browse by Hot Regoins
- Private Sourcing Events
- Sell on GoldSupplier.com
- How to Sell
- Post Products
- Manage Products
- Manage Groups
- About
- About Us
- Link to Us
- Contact Us
- Sitemap
- Please Enter your Email Address
- Please enter the content for your inquiry.
We will find the most reliable suppliers for you according to your description.
Send Now-
Emily Chow
Welcome to my shop! Glad to serve you!Please send your question!
Your message has exceeded the limit.
Your message has exceeded the limit.
-
-
Your inquiry content must be between 20 to 5000 characters.Send Now.
-
Please input the mailbox.
-