Home > Products > -Chemical > Oil soluble polyurethane grouting material waterproofinf agent for construction
Oil soluble polyurethane grouting material waterproofinf agent for construction
- 5000000 Kilogram / Kilograms per Month
- Incheon Busan
- T/T
Product Details
Place of Origin: | Gyeonggi-do, South Korea | Main Raw Material: | Polyurethane | Usage: | Building Coating |
Application Method: | Other, Injection (water stop) | State: | Liquid Coating | Brand Name: | DAEHWA |
Model Number: | DHP-2000 |
Product Description
Single Component Rigid Polyurethane Foam
High pressure waterstops
Leakage Crack Waterstops1 Component Type Polyurethane
Product Information
DHP-2000 is a single component hydrophobic water cut-off grout and soil stabilization grout based on a MDI (methylene-dephenylisocyanate) polyurethane. Upon contact with water DHP-2000 reacts to a foam while expanding its volume up to 30 times. The cured material is semi flexible and of a constant volume. Since water is not a component of the foam structure, the cured material is essentially not effected by water or dryness. The reacted material does not shrink or swell.
Characteristics
Contraction rate after hardening is the lowest in this industry. |
By using small amount of distinctive additive that is invented by our research team, hardened foam won't get decomposed in water. |
Since it forms high density Closed Cell Foam, nor water and moisture can penetrate into it. |
It is very easy to remove hardened substances of flowed Foam Waterstop out of crack spot. |
Since it has low viscosity, it is easy to inject. |
Usage
All concrete structure's cracked leakage spot with no vibration for waterstop repair.
Application Area
Use for the cracks water stop of concrete structures and wster stop treatment for joint areas, wet areas and areas of considerable leaks, and can be used in the following areas. |
Waterstops for leaking section of basement parking lot and underground concrete structure. |
Waterstops for crack leakage section of structure caused by vibration. |
Waterstops for leakage of concrete joint section. |
Waterstops for leakage section where humidity and dryness is mixed up together. |
Property Data | |
Classification | Base Value |
Exterior Appearance | Brown Transparent Liquid |
Mixing Rate | 1 Component Type |
Viscosity | 350 ± 50 |
Specific Gravity | 1.14 ± 0.1 |
Tensile Strength(kg/ | 16.5 |
Elongation Percentage | 30% or Under |
Packing Unit | 20KG / 10KG |
Foaming Percentage(%) | 3300% |
Reaction Data on a Different Temperature Conditions | ||||
Temperature Conditions | 5°C | 15°C | 25°C | 30°C |
Foaming Starts(sec) | 50 | 27 | 19 | 15 |
Foaming Ends(sec) | 320 | 245 | 208 | 185 |
Foaming Percentage | 2800 | 3300 | 3500 | 3700 |
Viscosity | 900 | 450 | 275 | 210 |
Using Material
It is specially designed to endure high pressure that is applied. Injected resin won't flow backward and this packer is also specially designed not to leak resin around stabilized and fixed packer. |
This is 1 component type high-pressure injection equipment that is specially manufactured to fill on a leakage and fracture spot by using polyurethane foam and epoxy injection material. |
Construction Guideline
Preforation
Perforate around leaking and fracturing spot and fixate packer. Normally when injecting polyurethane foam, it is injected through packer generally. During the perforation use hammer drill and make holes with same diameter. External diameter of Drill Bit should be 10mm. Perforation angle between concrete surface and crack should keep 45 degree angle or under. If it is possible, then make position of perforation hole that contacts crack as thick as 1/2~2/3 of concrete thickness. If the concrete thickness is less than 10cm then directly perforate to fractured spot. If the thickness is 10cm~50cm, perforate in the distance of 1/5 thickness of the concrete. Conduct it around fractured spot with 20cm interval and perforate in zigzag.
Packer Installation
Select the suitable packer out of various kinds of packers that suits the most according to field circumstance. And use T-box wrench and firmly tighten up the packer to perforated hole and make sure not to bounce off by counter pressure. (It might get damaged if it is tightened too hard.)
Polyurethane Injection
Inject DHP-2000 Rigid Foam Type by using high-pressure injection equipment or grease gun. Maintain initial injection pressure about 40kg/cm²÷ and keep injecting until waterstop material flows out through fractured spot. Halt injecting for a few minutes when DHP-2000 Rigid Foam Type flows out grossly between cracks during first PACKER injection, then injected foam will foam completely and it will become as seal material. For next injection operation, DHP-2000 Rigid Foam Type will fill up the cracks well enough. After 5 minutes, start to re-inject. You can ignore the chemicals that leaks out little bit, even you can check injection status. If the crack is very big then conduct sealing before injection. If the waterstop is injected properly, make sure to check the following steps in orders. |
Does the water inside of the crack come out caused by Polyurethane Foam Waterstop injection! |
Does the injected Foam react with water and come out from the cracks after gradually foaming! |
Finally, does the undiluted liquid of Polyurethane Foam slides out between the cracks before it starts foaming! |
If it is so then the injection is properly done. |
Removing Packer
Use vice pliers as a tool or bend off or use hammer to remove it.
If there is wet spot left then inject Polyurethane Foam again.
Finishing Opreation
Remove DHP-2000 Rigid Foam Type that is smeared around cracked area. Spread with flexible sealing material (DH-CF30 Crack Cover Material)
Cleaning
All the equipments and tools that are used for this operation should be cleaned when the operation is finished. Detergent such as M.E.K, Acetone, Xylene, Toluene and urethane thinner should be used when cleaning. If the Foam is smeared on your skin during the performance, wash it immediately with flowing water. Used injection equipment should need to be stored after filling up the hose, pump and medical fluid container with Engine Oil and hydraulic oil.
Cautions
- When you treating medical fluid, make sure you wear protective helmet, goggle clothes and other protective devices.
- If the medical fluid is smeared on your skin, wash it off immediately and clean up with soapy water.
- All the hand tools and equipments that are used for this operation should be cleaned with thinner thoroughly.
- If you are working in sealed room, then make sure to conduct constraint ventilation for clean air.
- If the medical fluid is smeared on your skin and causes skin trouble, then you should go see specialist for prescription.
- If the temperature is below 5°C, then you must artificially raise up the temperature of medical fluid. This way you can get proper Pot Life.
- If the atmosphere temperature is high and the area is humid, Pot Life of medical fluid quickens. On the contrary, Pot Life will slow down in low temperature area.
- Be aware of it before you conduct the operation.
Storing Method
Recommended temperature for storage is 10~25°C with no moisture. Store it in cool area. Storing period is about 6 months in sealed condition however it can be corrupted according to storing area and conditions. Preferably use it as soon as possible. This product is packed with nitrogen gas. Once seal is removed, then use it as soon as possible.
Contact Us
- DAEHWA PRECISION CO,. LTD.
- Contact nameJae In Cha
- Phone82-31-7771155
- AddressSentechcity B110,B111, 513-15 ,Sangdaewon-dong, Jungwon-gu
-Chemical | -Grouting Equipments | -Injection Pump | New Products |
- Chameleon pearl pigment for car painting and cosmetic
- Flame retardant horseshoe grease caulking asphalt mastic PVC waterproofing horseshoe grease no heat oil no boil expansion joints
- Chameleon pearl pigment for car painting and cosmetic
- Chameleon pearl pigment for car painting and cosmetic
- Chameleon pearl pigment for car painting and cosmetic
- Chameleon pearl pigment for car painting and cosmetic
- Chameleon pearl pigment for car painting and cosmetic
- Good Power of Hiding Temperature Resistance Whole sale Pigment for Car Paint
- Good Power of Hiding Temperature Resistance Whole sale Pigment for Car Paint
- Good Power of Hiding Temperature Resistance Whole sale Pigment for Car Paint
- Non-toxic Good Power of Hiding Pearlescent Pigment for Body Brushwork
- Non-toxic Good Power of Hiding Pearlescent Pigment for Body Brushwork
- Non-toxic Good Power of Hiding Pearlescent Pigment for Body Brushwork
- Good Power of Hiding Temperature Resistance Whole sale Pigment for Car Paint
- Guaranteed Quality Aluminum Paste for automotive coatings
- High Quality Direct Factory Aluminum Paste for automotive painting
- High Quality Direct Factory Aluminum Paste for automotive painting
- Good Power of Hiding Temperature Resistance Whole sale Pigment for Car Paint
- Direct Factory Powder Form Solvent Mixing Colored Aluminum for ink coating
- Hot Sale Factory Direct Aluminium Paste For Automotive Refinish Paints
- High Lustre Scintillant Pearlescent Pigment for Body Painting
- Non-toxic Good Power of Hiding Pearlescent Pigment for Body Brushwork
- Hot Sale Factory Direct Aluminium Paste For Car Painting
- Superior Quality Water Color Powder Pearlescent Pigment for Eye Shadow
Popular Searches
Recommended Products
- Laboratory heating furnace muffle furnace series products
- sodium chloro phenylsulfonyl azanide CAS 127-52-6 Chloramine B
- Edetic acid disodium salt C10H16N2O8 Edetic acid
- 1H-Benzotriazole BENZOTRIAZOLE (BTA) CAS 95-14-7 C6H5N3
- Paraformaldehyde White Powder cas 30525-89-4 Inorganic Chemicals
- Sebacic Acid Powder CAS111-20-6 Granular/Powder Sebacic Acid 99.5%
- Chameleon pearl pigment for car painting and cosmetic
- HAISU Silica SPE Cartridges, Graphitized carbon black SPE filler 40-120μm
- HAISU Silica SPE Cartridges, PSA, 40 - 63 µm, 60 Å PSA ethylenediamine-N-propyl siliconebonded filler
- HAISU Silica SPE Cartridges, C18, 40 - 63 µm, 60 Å
- HAISU Silica SPE Cartridges, C18, 40 - 63 µm, 60 Å
- Silicagel C18 (17%C) Monomeric, 40 - 63 µm, 100 Å
Find Similar Products By Category
- Chemicals > Coating&Paint
- Buy on GoldSupplier.com
- How to Buy
- Browse by Catagories
- Browse by Hot Regoins
- Private Sourcing Events
- Sell on GoldSupplier.com
- How to Sell
- Post Products
- Manage Products
- Manage Groups
- About
- About Us
- Link to Us
- Contact Us
- Sitemap
- Please Enter your Email Address
- Please enter the content for your inquiry.
We will find the most reliable suppliers for you according to your description.
Send Now-
Jae In Cha
Welcome to my shop! Glad to serve you!Please send your question!
Your message has exceeded the limit.
Your message has exceeded the limit.
-
-
Your inquiry content must be between 20 to 5000 characters.Send Now.
-
Please input the mailbox.
-