Inductors for Power Circuits SLF7045T-221MR33-PF SMD Power Inductors

 SLF7045T-221MR33-PF

Inductors for Power Circuits

Wound Ferrite

SLF Series

SLF7045 Type

REMINDERS FOR USING THESE PRODUCTS

Before using these products, be sure to request the delivery specifications.

SAFETY REMINDERS

Please pay sufficient attention to the warnings for safe designing when using these products.

The storage period is less than 6 months. Be sure to follow the storage conditions (Temperature: 5 to 30°C, Humidity: 10 to 75% RH or

less).

If the storage period elapses, the soldering of the terminal electrodes may deteriorate.

Do not use or store in locations where there are conditions such as gas corrosion (salt, acid, alkali, etc.).

Before soldering, be sure to preheat components.

The preheating temperature should be set so that the temperature difference between the solder temperature and chip temperature

does not exceed 150°C.

Soldering corrections after mounting should be within the range of the conditions determined in the specifications.

If overheated, a short circuit, performance deterioration, or lifespan shortening may occur.

When embedding a printed circuit board where a chip is mounted to a set, be sure that residual stress is not given to the chip due to

the overall distortion of the printed circuit board and partial distortion such as at screw tightening portions.

Self heating (temperature increase) occurs when the power is turned ON, so the tolerance should be sufficient for the set thermal

design.

Carefully lay out the coil for the circuit board design of the non-magnetic shield type.

A malfunction may occur due to magnetic interference.

Use a wrist band to discharge static electricity in your body through the grounding wire.

Do not expose the products to magnets or magnetic fields.

Do not use for a purpose outside of the contents regulated in the delivery specifications.

The products listed on this catalog are intended for use in general electronic equipment (AV equipment, telecommunications

equipment, home appliances, amusement equipment, computer equipment, personal equipment, office equipment, measurement

equipment, industrial robots) under a normal operation and use condition.

The products are not designed or warranted to meet the requirements of the applications listed below, whose performance and/or

quality require a more stringent level of safety or reliability, or whose failure, malfunction or trouble could cause serious damage to

society, person or property.

If you intend to use the products in the applications listed below or if you have special requirements exceeding the range or conditions

set forth in the each catalog, please contact us.

(1) Aerospace/Aviation equipment

(2) Transportation equipment (cars, electric trains, ships, etc.)

(3) Medical equipment

(4) Power-generation control equipment

(5) Atomic energy-related equipment

(6) Seabed equipment

(7) Transportation control equipment

(8) Public information-processing equipment

(9) Military equipment

(10) Electric heating apparatus, burning equipment

(11) Disaster prevention/crime prevention equipment

(12) Safety equipment

(13) Other applications that are not considered general-purpose

applications

When designing your equipment even for general-purpose applications, you are kindly requested to take into consideration securing

protection circuit/device or providing backup circuits in your equipment.

REMINDERS

(3/9)

INDUCTORS

20160411 / inductor_commercial_power_slf7045_en.fm

Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use.

Please note that the contents may change without any prior notice due to reasons such as upgrading.

Inductors for Power Circuits

Wound Ferrite

FEATURES

Magnetic shield type wound inductor for power circuits.

Product lineup allows for various usages.

APPLICATION

Thin-screen TV, LCDs, AV equipment, gaming equipment, other electrical devices

PART NUMBER CONSTRUCTION

OPERATING TEMPERATURE RANGE, PACKAGE QUANTITY, PRODUCT WEIGHT

Operating temperature range includes self-temperature rise.

The Storage temperature range is for after the circuit board is mounted.

Product compatible with RoHS directive

Compatible with lead-free solders

Overview of SLF7045 Type

SLF 7045 T - 3R3 M 2R5 - PF

Series name L×W×H Dimensions Packaging style Inductance Inductance

tolerance

Rated current Internal code (mm) (μH) (A)

7045 7.0×7.0×4.5 T Taping 3R3 3.3 M ±20% R47 0.47

100 10 N ±30% 2R5 2.5

101 100 150 15

Type

Temperature range Package quantity Individual weight

Operating

temperature

（°C）

Storage

temperature

（°C） (pieces/reel) （g）

SLF7045 –40 to +105 –40 to +105

Factory Pack Quantity:  1000

Preheating:

temp. t1  150℃

t2 180℃

time  t1: 60-120s

soldering

temp. t3  230℃

time  t2  30s

peak

temp. t4 250℃

time T3 5s

ELECTRICAL CHARACTERISTICS

CHARACTERISTICS SPECIFICATION TABLE

220uh

tolerance: ±20%

l measuring frequency: 100khz

dc resistance: (Ω)±20%： 0.52

rated current: isat (a) max. 0.33

itemp (a) max: 0.45

Rated current: smaller value of either Isat or Itemp.

Isat: When based on the inductance change rate (10% below the initial value)

Itemp: When based on the temperature increase (Temperature increase of 20°C by self heating

Factory Pack Quantity:  1000