Mitsubishi High Speed Counter Module QD62

Mitsubishi High Speed Counter Module QD62

Mitsubishi QD62 performance parameters

Mitsubishi High Speed Counter Module QD62

◇ 2 channels, 200kpps

◇ 5/12/24VDC input, drain transistor output

Summary: Conduct high-speed counter combination for high-speed disturbances.

The control line for external coding combination positioning may:

The 32-bit counting range input channel 2 is equipped with independent signed binary (-32-bit 2147483648~2147483647) counting possibilities.

Selection of input method: The input method for 1-phase 1-fold/1/2-phase 2-fold 1-fold/2/2-phase 2-fold 4-fold/CW/CCW can be selected.

Selection of counter form:

Any form of linear counter or Ring counter can be selected.

Switching function of Mitsubishi high-speed counter module QD62 counting speed:

The switching of counting speed may be achieved by counting pulses with slow low cycles that rise/fall from high-speed pulses.

Interrupt function of CPU combination:

When the pre-set count value reaches, the CPU unit outputs the interrupt signal and the interrupt program starts.

Counter selection function:

Select one of the four counter functions to use.

Control from external terminals:

The pre-set terminal/function of external terminals and the selection of custom function/counter function can be executed for starting terminal voltage.

Improvement of maintainability:

The fuse of the external output unit is detected to be broken, and the input signal X and the display LED of the unit are notified.

Counting speed conversion settings 200k (100-200kppsk), 100k (10k-100kpps), 10k (below 10kpps)

Counting input signal phase 1 phase input (1/2 36883X 36883X), 2 phase input (1/2 36883X 36883X/4 36883X), CW/CCW input

Signal level（ φ A， φ B) DC5/12/24V2~5mA

DC24V input ON/ON current voltage 21.6~26.4V/2~5mA

Discount voltage/OFF current below 5V/0.1 mA

DC12V input ON/ON current voltage 10.8-13.2V/2-5 mA

Discount voltage/OFF current below 4V/0.1 mA

DC5V input ON/ON current voltage 4.5-5.5V/2-5 mA

Discount voltage/OFF current below 2V/0.1 mA

Counter counting speed () 200kpps, 100kpps, 10kpps

Count range 32-bit signed binary (-2147483648~2147483647)

Type UP/DOWN preset counter+Ring counter function

***Subtotal pulse width (50) compared to coil 200kpps: 5 μ S (ON/OFF 2.5 each μ s) At 2-phase input, * * * * small phase difference: 1.25 μ s

100kpps：10 μ S (5 on/off each μ s) At 2-phase input, * * * * small phase difference: 2.5 μ s

10kpps：100 μ S (50 on/off each μ s) At 2-phase input, * * * * small phase difference: 25 μ s

Consistency detection comparison range 32-bit symbol pay binary

Comparison result set value

Set value=count value

Set value>count value

External input preset DC5/12/24V2~5mA

Start of function DC5/12/24V2~5 mA

External output consistent output transistor (heat sink type) Output: 2 points/channel

DC12/24V0.5A/1 minute, 2A/1 inch

External circuit connection method: 40 pin connector

Suitable connectors: A6CON1, A6CON2, A6CON3, A6CON (sold separately) 4

Number of occupied slots: 1

Input and output occupancy points: 16 points

DC5V internal consumption current: 0.30A

External dimensions H * W * D: 98 * 27.4 * 90mm

Weight: 0.11 kg

1. Mitsubishi full series PLC, frequency converter, human-machine interface, servo system.

2. Xinjie PLC, frequency converter, human-machine interface and servo system.

3. Delta PLC, frequency converter, human-machine interface and servo system.

4. Wellington human-machine interface and Hytec human-machine interface.

Mitsubishi servo motor HG-JR15K1MB;

Mitsubishi servo motor HG-JR11K1MB;

Mitsubishi servo drive MR-J4-11KA

Mitsubishi servo drive MR-J4-11KB

Mitsubishi servo drive HG-KR-23J with oil seal

Mitsubishi servo store HG-KR053

Mitsubishi servo motor HG-KR73BJ with oil seal

Mitsubishi servo motor HG-SR102BJ with oil seal

Mitsubishi MR-J4-15KB servo driver

Mitsubishi PLC (programmable controller) A, R, Q, L, CC-LNK, FX3SA, FX3G, FX3G, FX3U, FX5U and other series;

Mitsubishi frequency converter A840, E840, F840, E740, D740, D720 series; Mitsubishi touch screen GT2000 series; Mitsubishi servo motor JE, J4 series.

Mitsubishi programmable controller: FX3GA, FX3GE, FX3G, FX3U, FX3UC, FX2NC, A, Q, CC-LINK remote module and other series

Mitsubishi variable frequency governor: FR-L700, FR-A700/500, F700/500, E700/500, D700/500, S500 and other series;

Man-machine interface: GOT2000, GOT16, GOT15, GOT12, GOT11, GOT10, A900GOT, F900GOT and other series;

AC servo system: MR-J4, MR-JE, MR-J3, MR-J2S, MR-E, MR-ES and other series;

Tension control system: LE-40MTA (B), LD-FX, LD-50PAU and other series:

Low-voltage electrical appliances: S-N, TH-N, etc.