VAG Commander 7.5

UFODIAG Commander for VAG is a Windows PC based diagnostic software for the vehicles from VAG. With the help of this tool you can perform operations with vehicles from the VAG group, which are in most cases unsupported from the producer diagnostic testers. The ABRITES Commander for VAG provides you also a full diagnostic capabilities for VAG-vehicles.

Standard diagnostic functions:

Connect to the device using KWP2000 over TP2.0,

KWP2000 over TP1.6, UDS over ISO transport protocol (CAN),

KWP1281 or KWP2000 over K-Line

For all electronic control units reading identification data

For all electronic control units read error (DTCs)

For all electronic control units clear error (DTCs)

Scan all units

Broadcast requests

Measured values

Adaptation

Special functions:

Instrument CAN
- With this function you can establish diagnostic session with the Instrument cluster using KWP2000 over TP2.0
- You can read current odometer value
- You can change odometer value
- Read/Program memory of instrument cluster immobilizer
- Reading security access code of the IMMOBILIZER
- Read/Write immobilizer related data

EZS - Kessy (Q7/A6/Allroad)
- With this function you can prepare dealer key/learn dealer key
- Read/Write eeprom from EZS - Kessy (Q7/A6/Allroad)

Instrument K-Line
- With this function you can establish disgnostic session with the Instrument cluster via K-Line (KWP1281 or KWP2000)
- You can Read/Change odometer value
- Read PIN code
- Read/Write eeprom
- Read ROM/Flash from the Instrument cluster

Engine Control Unit
- Read EDC17/MED17 flash memory
- Read/Write of flash memory (EDC15, EDC16 all types Read/Write Flashmemory via OBDII (K and CAN). Calculation of
checksums while programming, ME7.1.1, MED9.x, ME7.5)
- Read/Write flash counters (EDC16)
- Read/Write eeprom (VAG-EDC15x, VAG-ME7.1.1, VAG-ME7.1, VAG-ME7.5, VAG-Cartronic ME7.8.)
- Extracting Security access code / PIN (EDC15, ME7.x, VAG-Cartronic ME7.8, EDC16, EDC17, MED9.x, Simos PPD)
- Extracting Component security bytes (EDC15, ME7.x, VAG-Cartronic ME7.8, EDC16, MED17.5.1, MED 9.x, Simos PPD)
- Enable/Disable immobilizer (EDC15, ME7.x, EDC16)
- Odometer correction (EDC15, EDC16)

Kessy adaptation
- This function can be used for adaptation of brand new kessy units to the car. This adaptation can be by CAN TP2.0, K-KWP2000 and also can be used with Porsche Cayenne.

TV activation ED1/ED2
- Using this special function you can change speed limit of MMI compatible vehicles to change speed where TV becomes OFF

Key learning
- With this function you can learn key/transponder to the vehicle

Dump tool
- With this function you can calculate security access codes, change odometer and so on from EEPROM dump from the correcponding unit

Airbag
- With this special function you can Read/Write EEPROM memory of the airbag module
- Clear the crash data of the airbag module

Custom Read/Write
- Using this application you can read/program memory in some electronic control unit

PIN Convertor

Service interval
- Using this function you can perform reset of the service

reminder, reset of the service interval parameters or change service interval options

Remote control adaptation
- Using this application, you can learn remote controls

Navigation
- Using this application, you can enable/disable the “Eject” button of the “Navigation” system

Cruise control system
- Using this application, you can activate/deactivate a cruise control system and change the related
steering wheel electronics( SWE) configuration if SWE unit is available

Brake pads change
- Using this application, you can “Open rear parking brake for pad change”, “Close rear parking
brake”, perform “Parking brake function test”