Contact Platform Support
Help Center5.5 kW Slurry Beater AAC Ball Mill Machine 2400 mm 1257 mm 2684 mm
Related Products
-
High Efficiency AAC Dry / Wet Grinding Ball Mill Machine For SilicateNegotiableMOQ: 1 Set -
Autoclaved Aerated Concrete Mining Stone Jaw Crusher For AAC Block Making PlantNegotiableMOQ: 1 Set
-
Dust Remover Device Ball Mill Machine / AAC Sand Lime Brick Making PlantNegotiableMOQ: 1 Piece
-
Firmed AAC Powder Grinding Mill Machine / AAC Slab Making MachineNegotiableMOQ: 1 Set
-
High Speed Cement Ball Mill Machine AAC Chain / Belt Bucket ElevatorNegotiableMOQ: 1 Set
Certification:ISO9001：2008
slurry beater AAC Ball Mill Machine / Autoclaved Aerated Concrete Block Plant
Mixer in the mortar mixing tank
1. Function
The mixer in the mortar mixing tank (see attached drawing) is a special mixer whose function is to get ground lime and water etc thoroughly mixed into mortar to be poured so that it can be made into autoclave aerated concrete blocks.
2. Technical specifications
a) Maximum overall dimensions:
2400 mm (length) × 1257 mm (width) × 2684 mm (height)
b) Mass: 386.4 kg
c) Cycloidal-pin gear speed reducer
i.Type: BLY27-35-5.5
ii. Motor: power 5.5 kW, speed: 1470 rpm
iii.Speed ratio: i=35
d) Rotation speed of the mixer: 42 rpm
3.Structure
The mixer is composed of the following parts: cycloidal-pin gear speed reducer, shaft, steel channel and mixer.
a) The speed reducer is of a cycloidal-pin gear type and is vertically mounted.
b) The shaft and the mixer are welded together.
4.Operation
The mixer is used for the purpose of mixing ground lime and water into mortar to be used for the pouring so that it can be made into autoclave aerated concrete blocks.
The mixer is driven by the cycloidal-pin gear speed reducer. The speed reducer rotates in a counterclockwise direction (looking from the top), driving the mixer to rotate so that ground lime and water are thoroughly mixed into mortar.
5.Trial running and adjustment
a) Trial running:
When the mixer is fixed together, rotate it without any load. The speed reducer should be able to rotate normally without any jamming or abnormal noise. The mixer should not tilt and should rotate in a balanced way without jerking or swinging.
b) Adjustment
i.If jamming or abnormal noise occurs in the speed reducer, disassemble and check it or add pads on the bearing seat for adjustment.
ii.If the mixer tilts or shakes, add pads between the bearing seat and the beam frame for adjustment.
6.Maintenance
a) Daily care
i.Do not leave any mortar in the tank at the end of each shift lest the mortar deposit and destroyed the machine when restarted.
ii.Re-fill lubricating oil whenever its level is found to be lower than the marking. The lubricating oil should be replaced every six months.
iii.The tank and the mixer should be rinsed clean after each shift.
b) Maintenance:
A weekly check of the fasteners at all locations should be performed. Loose fasteners should be retightened and damaged ones should be replaced.
Safety:
Switch off the power and stop mixing before doing the rinsing.
Send Inquiry to This Supplier
You May Also Like
-
Standard Tagging Gun ,Green Clothing Tag Pin GunNegotiableMOQ: 50 Pieces
-
2L Automatic Adjustable Time Centralized Lubricant Knitting MachinesUS$ 50 - 150MOQ: 1 Piece
-
Mayer Circular Knitting MachineUS$ 15,000 - 29,999MOQ: 1 Set
-
Rope Machine for Sugar Cane BindingNegotiableMOQ: 1 Unit
-
DW 1318 Laser Cutter BedUS$ 8,000 - 10,000MOQ: 1 Set
-
Manufacturer Direct Selling High-speed Knitting Machine, Three-strand Twisting Rope Machine, Rope Belt MachineNegotiableMOQ: 1 Set
-
Green House Agro Shade Net Making MachineUS$ 27000 - 30000MOQ: 1 Set
-
Taifan Single Terry Towel Circular Knitting MachineUS$ 15000 - 18000MOQ: 1 Set
-
Hot Sale Hosiery Machines Socks Knitting Machine Automatic Sock Knitting MachinesUS$ 2999 - 3999MOQ: 1 Set
-
Stoll Automatic Computerized Flat Knitting Machine Stoll Cms 520c E3 Woolen Knit SweaterUS$ 12200 - 12300USDMOQ: 8 Sets
