Contact Type High Performance Ignition System Flame Scanner Detector With Self Test Types Of Gas Fue
Contact Type High Performance Ignition System Flame Scanner Detector With Self Test Types Of Gas Fuel
Specifications:
|
Sr. |
Name |
Model |
Description |
|
1 |
Falme scanner |
XHT-1 |
Contact type flame detector |
|
2 |
Falme scanner |
XHT-2 |
Micro flame ionization detector |
|
3 |
Falme scanner |
XHT-3 |
UV type, gas and oil flame detection |
|
4 |
Falme scanner |
XHT-4 |
Infrared type |
|
5 |
Falme scanner |
XHT-5 |
Visible light, infrared hybrid, detection of oil, coal and rich in visible light of the gas flame; Also applies to low nitrogen oxide NOx burn |
XHT Flame detection device of power station boiler of large combustion equipment of furnace safety supervisory system and a variety of industrial furnace,the key equipment of burner flame detection.The device according to the physical properties of the combustion flame detection,When the flame burning state does not meet the normal condition or flameout,it will show signal by some mode (Switch quantity and analog quantity),as logic judgment of the fault alarm or furnace safety supervisory system(FSSS).
Technical advantages:
1. Using the latest software and hardware identification technology, with high reliability.
2. With a self-test function, and has higher safety.
3. Adapt to all types of fuel, including gas, fuel, coal and other fuel types.
4. Detection mode, including ion type, light type and image type.
Applications:
XHT Flame detection device is widely used in electric power,Iron and steel, metallurgy, petrochemical and other industries a variety of boiler,burner flame detection, and also can be applied to various occasions the need for flame detection.
1.XHT-1 contact type flame detector
1.)basic configuration:Flame detector 1pcs ,probe 1pcs
The probe also known as ionic conducting rod, consist by the probe, a center electrode, ceramic tube,stainless steel outer sleeve.,usually the diameter is dia18 , dia 16 , Special occasions can be designed according to customer requirements.
2.) Performance parameters:
The fire detecting device consists of a flame probe, cable and signal processing box.
Working principle:Put he probe needle into the flame zone,Use of burning high temperature gasification to produce ionization characteristics,conducting electrode, flame signal, ignition. Then exit probe out flame zone, to avoid the electrode failure bec of high temperature pollution.
Contact type fire detector is only applicable to gas condition
|
Name |
Performance parameters |
|
Sensitivity |
>2uA |
|
Reaction time |
<2s |
|
Probe temperature |
1200℃ |
|
Probe method |
Short time contact |
|
Switch output |
A set normally open / normally closed contact, capacity; AC220V /50HZ , 2A DC24V , 2A |
|
probe rod diameter |
dia 18 , dia 16 |
|
Power |
AC220V ± 10% , 50HZ |
|
Power waste |
< 15W |
Send Inquiry to This Supplier
You May Also Like
-
ASKAWA CIMR-AC4A0414AAA AC Inverter NegotiableMOQ: 1 Piece
-
Suitable For Outdoor Use Variable Frequency Ac Power SupplyUS$ 1 - 10000MOQ: 1 Piece
-
Power InverterNegotiableMOQ: 2500 Pieces
-
2014 High Quality Pure Sine Wave Power Inverter 12v 220vUS$ 1 - 1,000MOQ: 100 Units
-
E82EV751_2C E82EV751-2C InverterUS$ 1 - 2MOQ: 1 Piece
-
New 10A 12V 24V 36V DC Electric Motor Speed Controller for Electric Motor PWM Control DC Motor DriverUS$ 1 - 100MOQ: 100 Units
-
1000W Pure Sine Wave Power Inverter DC 12V to AC 230V New Car Caravan A1766US$ 90.93 - 91.53MOQ: 300 Pieces
-
12 Volt 220 Volt Inverter, Pure Sine Wave Inverter, Dc to Ac Power InverterNegotiableMOQ: 1 Piece
-
Irrigation Equipment Center Pivot Parts of Frequency Convertor & Pressure Sensor SystemNegotiableMOQ: 1 Set
-
Sell el Inverter DriverUS$ 2 - 12MOQ: 5 Pieces