Contact Platform Support
Help CenterFlared Stainless Steel Tube Thermistor Temperature Sensor Probe For Air , Gas
Related Products
-
Aluminum Tube Thermistor Temperature Sensor Probe / NTC Temperature SensorNegotiableMOQ: 1 Set -
Flanged Stainless Steel NTC Thermistor Temperature Sensor For ConfigurationsNegotiableMOQ: 1 Piece
-
Threaded Stainless Steel Tube Thermistor Temperature Sensor Probe For Liquid MeasurementNegotiableMOQ: 1 Piece
-
Threaded Fitting NTC Temperature Sensor Probes / NTC Thermistor ProbeNegotiableMOQ: 1 Piece
-
Glass Coated NTC Temperature Sensor With Protection Tube , RTD Temperature ProbesNegotiableMOQ: 1 Kilogram
Certification:ROHS,SGS
Flared Stainless Steel Tube Thermistor Temperature Sensor Probe For Air , Gas
Quick Detail:
Flared stainless steel tube thermistor temperature sensor probe, \"bullet\" style temperature probe for air, gas or liquid. Typical application coffee maker, tea kettle, water heater boilers, milk warmer, cooking equipment, and other home appliance.
Description:
NTC Thermistor can be assembled in housing in a variety of configurations for temperature sensing, measurement, detection, indicator, monitoring and control. Thermistor temperature sensor probe assemblies can conveniently attach to or be an integral part of any system to monitor or control temperature.The choice of assembly is dependent on the application. The primary factors which determine the optimum configuration of a thermistor assembly are the operating environment, mounting, time response and minimum dissipation constant.
The two factors which do vary considerably with thermistor sensor probe assembly design are time constant and dissipation constant. The time constant will typically be of greater duration in encapsulated thermistors. This is, of course, due to additional mass surrounding the thermistor element; therefore, extending the thermal transfer time. Dissipation constant will also be greater in assemblies. The additional housing mass serves well as a heat sink. Greater power is therefore required to induce self-heating. Both time constant and dissipation constant will vary with the selected thermistor and housing. Heat transfer properties of the housing, thermistor location, mass and wire type determine these constants.
Applications for temperature sensing include air temperature sensors, surface temperature sensors and immersion temperature sensors. Housings for air temperature sensors are often simple, inexpensive devices such as molded plastic shells, deep-drawn brass or aluminum cylinders, or even stainless steel tubes. Surface temperature sensors are designed to match the contour of the surface to be sensed, whether it\'s flat, curved, or round. Mounting holes or clips are often used to simplify installation of the sensor. Immersion temperature sensors are designed so that the sensing element will be surrounded by the medium to be sensed, often times a liquid. The sensing portion will normally protrude through a hole or orifice while a portion of the assembly will remain outside the medium to allow for the signal to be read. Immersion housings are usually threaded to allow them to be screwed into a hole or opening. Immersion part requests to be liquid and humidity prevention.
The material used for the housing will be dependent upon the temperature range needed, response time, cost, and special considerations such as UL, FDA or NSF requirements in food and/or medical applications. Some of the materials available include stainless steel, copper, plastic, teflon, brass, aluminum, epoxy and heat shrinkable tubing.
Applications:
Flared stainless steel tube thermistor temperature sensor probe, \"bullet\" style temperature probe for air, gas or liquid. Typical application coffee maker, tea kettle, water heater boilers, milk warmer, cooking equipment, and other home appliance.
Specifications:
|
Resistance @25C |
Beta Value |
Thermal time constant |
Dissipation factor |
Operating temperature range |
|
10K ohm±2% |
3977K±1% |
12 Sec |
5 MW/C |
-30C～+105C |
Note: Alternative ratings on resistance, Beta value and cable length upon request.
Drawing
Competitive Advantage:
Factory supply directly Completed certificates such as UL,VDE,SGS,etc and high quality available Quick delivery Best after-sales services OEM & ODM available
Send Inquiry to This Supplier
You May Also Like
-
SICK ICR845-2E1020 SICK Industrial Barcode Scanner for Logistics & AutomationNegotiableMOQ: 1 Piece
-
1001995247 1001063375 1002807652 1001999981 612630060035 331001000463 1001999976 1001954223 1001995248 1001251569 1002077919 1001996818 1001999976NegotiableMOQ: 1 Blade
-
Sick WSE4S-3P3130H Order Number: 1052888 Product Family: W4S-3 Inox Hygiene Product Family: Photoelectric SensorsUS$ 100 - 200MOQ: 1 Piece
-
Pressure SensorNegotiableMOQ: 2000 Pieces
-
20428461 20732304 20428462 Heavy Duty Truck Sensor Parts Fuel Tank Level Sensor For VOLVONegotiableMOQ: 1
-
King Pigeon Temperature Humidity Transducer THI100 Temperature Humidity Detector Wireless SensorUS$ 2 - 31MOQ: 5 Pieces
-
Ultrasonic Position Liquid Level Position SensorUS$ 200 - 700MOQ: 1 Piece
-
Crank Oil Seal for Toyota Auto Parts Oem 90311-95012US$ 1 - 10MOQ: 1 Piece
-
SHT10 Humidity & Temperature SensorUS$ 1 - 2MOQ: 5 Pieces
-
Wholesales & Retails HCA131A High Performance Dual Axes Tilt Sensor Switch Led Light With Tilt Switch From Shenzhen FactoryNegotiableMOQ: 1 Piece
