Waterproof Eco Friendly Greenhouse Twin Wall Polycarbonate Sheet 4mm 8mm 10mm

 
 
Product details
1. Thickness: 4.0mm, 6.0mm, 8.0mm, 10.0mm,12.0mm.
2. Length: 3000mm,5800mm, 11800mm. 
3. Width:1220mm, 1560mm,1820mm,2100mm
4. Color: Clear, Green, Blue, Opal, Dark brown, etc. 
5. Special specification and color are available.
6. Gravity

 
 
 
Product Features

1. Good effect on heat insulation
2. Simply and convenient structure
3. Beautiful appearance
4. Energy saves
5. High light transmission
6. Good impact strength
7. Weather resistance, anti-UV.anti-fog
8. DIY available

Technical Features:

1) Light transmission: 12% to 80% depending on different colors and thickness

2) High impact resistance

3) UV protection layer: 50μm ,can filter about 99% ultraviolet radiation in sunshine

4) High heat insulation

5) Continuous use temperature: -40°C to 120°C

6) Can be cold bent

Applications:

1) Building/House skylights

2) Work shop/storehouse skylight

3) Roofing

4) Carports

5) Indoor partition

6) Cover of greenhouse

7) Cover of swimming pool

 
If you need DIY a greenhouse, you need:
1. 2mm strong aluminum frames with gutter system. 
2. 4mm/6mm UV protected twin wall polycarbonate sheet or 2mm/3mm pc solid sheet is light, strong, safe, and virtually unbreakable and easy to handle.
3. 1mm galvanized steel base can ensure maximum stability of your greenhouse.
4. Single sliding door and two adjustable windows for excellent ventilation.
5. Easy to assemble and DIY per the assembly Instructions.
6. Provide screwdriver for free. 

How to install the Greenhouse Covering?
1. Frame Spacing: When installing greenhouse covering, we recommend that the framing or trusses of your greenhouse frame be placed 16\"- 24\" apart. 
2. Flute Direction: We’ve found placing your greenhouse panels so that the flutes run perpendicular to your frame provides the maximum amount of strength for your structure. When attaching the screws to steel frame, we recommend using our 1\" screws with neoprene washers, which helps prevent water from leaking into the flutes. Our 1\" self-drilling screws are for installing greenhouse panels into metal framing. We suggest placing the screws about 18\" apart on the stringers and about 9\" apart on the perimeter. Be careful not to over torque the screws, or you may crush the greenhouse panel. 
3. Screw Hole: When temperature difference exceeds 8°C, all screw holes should be reamed to reserve space for expansion and contraction. Usually, the holes diameter should be larger than that of the screw stem by 20%. Fill up the holes, and cover the exposed portion with silicone compound to prevent detergents permeating which brings damage to PC sheets, and avoid gradual cracks. Screw heads should be larger than the stem by 1-1.5times .Use gaskets or washers to avoid the screw heads touching PC sheets directly .Don \'t use gaskets made of PVC
4. PC U-profile: Use U-profile to seal the open flutes. On all exposed fluting (4’ side of panels) we recommend you insert ¼\" of GE Silicone II \"clear\" caulking into flutes, to prevent water intrusion. Slide U-Trim over the ends of the greenhouse panels for a permanent cap. Secure U-profile with small zip ties by poking a small hole in the greenhouse panels with a large paper clip or small nail. Place each zip tie about one foot apart. Put caulking in all holes you create to stop water penetration.
5. PC H-profile (or PC upper & lower fastener): We sell the PC H profile (or PC upper & lower fastener) to join the long side of the PC sheet together and should run perpendicular to the greenhouse studs. It is meant to float between the panels to allow for expansion and contraction, so no screws go through the H-Channel. This locks them into place and can help prevent water leakage. If H-profile is difficult to slide on, spray groov