Contact Platform Support
Help CenterIndoor White Sandstone Waterproof Tile Adhesive , Bathroom Tile Adhesive
Related Products
-
Kitchen Floor Tile Adhesive / Sandstone Glue / Waterproof Pool Tile AdhesiveNegotiableMOQ: 1 Set -
Sandstone Gum Waterproof Tile Adhesive Synthetic Eco Friendly For CemeteryNegotiableMOQ: 1 Kilogram
-
Ceramic Wall Tile Adhesive , Heat Resistant Underwater Tile Adhesive Stone GlueNegotiableMOQ: 1 Metric Ton
-
Outdoor Strong Waterproof Tile Adhesive , Marble And Mosaic Tiles AdhesiveNegotiableMOQ: 1 Cubic Meter
-
High Bond Waterproof Tile Adhesive Non Toxic White Tile AdhesiveNegotiableMOQ: 1 Set
Certification:ISO
Indoor White Sandstone Waterproof Tile Adhesive For Bathroom
|
Product Name |
PB-04 Tough Sandstone Adhesive |
|
Appearance |
White, gray power |
|
Application |
Applied to all kinds of low water-absorption stone materials like large-sized artificial stones, culture stones, and natural stones |
|
Feature |
Strong cohesion force, material-saving, much safer and firmer, good anti-acid, anti-alkali, anti-infiltration and anti-aging function |
|
Hardening Time |
about 10min |
| Surface Preparation |
Smooth and firm, no dust, grease, release agents, batik material, etc. |
| Construction Temperature |
5℃~40℃ |
| Adjust Time |
about 15min |
|
Full curing time |
About 24h |
| Shearing strength |
>1.5MPA(14days) |
PB-04 Tough Sandstone Adhesive specially for bonding sandstone on interior and exterior wall and floor. Sandstone is low strength, not so heavy, low water-absorption and becomes black and mildewed when meets alkali. PB-04 is high bonding strength, low alkali and avoids the sandstone becoming black and mildewed. Suitable for bonding sandstone on cement mortar, concrete, Eterpan etc such strong substrates.
Features:
1, A new type strong stone adhesive, applied to all kinds of low water-absorption stone materials like large-sized artificial stones, culture stones, and natural stones.
2, No need to wet the brick wall, effectively improve the efficiency.
3, Strong bond ability, material-saving, much safer and firmer than the traditional cement adhesive, also can reduce the construct trash and the weight of the wall.
4, Good anti-acid, anti-alkali, anti-infiltration and anti-aging function.
5, Small shrinking rate, no cracking, can be used in cold and humid environment.
Application:
1, The adhesive for the cement plaster, brick and smooth cement surface.
2, The adhesive for low water-absorption surface and light weight board, like Eterpan, Pine Board and gypsum board.
Surface Treatment:
The substrate surface should be firm, dry and clean, no grease, no wax, and other loose materials.
Operation Process:
1, The ratio: PB-04: water=3.3: 1 (20kg powder, about 6kg water). Mixing and stirring them into paste, using an electric mixer to make uniform paste, put it aside for a few minutes and then a little stirring to gain the better effect.
2, Using a tooth scraper to scrap the adhesive onto the surface evenly, control within 1㎡, then push the stone above it.
3, For the tile or stone material with deep ditch, not only scrape the surface, but also the backside of the tile or stone.
Normal Amount:
|
Size of notched trowel |
Coverage(kg/m2) |
Technical parameter |
|
3mm×3mm |
1.7 kg/㎡ |
Adjusting time: 15 minutes |
|
Hardening time: 10 minutes |
||
|
6mm×6mm |
3.0 kg/㎡ |
Full curing time: 24 hours |
|
Waterproof; non-toxic |
||
|
10mm×10mm |
4.5 kg/㎡ |
Resistance to acids and alkali |
|
Shearing strength >1.5MPA(14days) |
Tips:
Bricks for wall using 3×3mm tooth scraper or 6×6mm tooth scraper.
Bricks for floor using 6×6mm tooth scraper or 10×10mm tooth scraper.
Cautions:
1, Make sure the smooth and vertical rate of the surface before operation.
2, Never mix the dry slurry with water for second use.
3, Check the mortar layer of the back side, make sure that have no cavitation.
4, Can not be walked on or filled crack unless finished after 24h.
Store Method:
Store in cool and dry place, unopened product can be saved for one year.
Packing:
Send Inquiry to This Supplier
You May Also Like
-
Custom 5ml 10ml 20ml 25ml 50ml High Borosilicate Glass Amber Volumetric FlaskUS$ 2.93 - 22.27MOQ: 100 Pieces
-
High Quality Competitive Price Plastic Conical Flask With Cap and MeasurementUS$ 3 - 10MOQ: 1 Piece
-
Laboratory GlasswareUS$ 0.1 - 0.9MOQ: 500 Pieces
-
Fluororesin Pfa Reaction Device, Acid-resistant and Corrosion-resistant Sealed Distillation Reaction Tank, 1l, With Sampling Funnel and Outlet ValveUS$ 553.85MOQ: 1 Piece
-
HC-K015 Factory Price Laboratory 500ml Chemistry Glass Guaduated Conical FlaskNegotiableMOQ: 1
-
NJbinglab PFA Erlenmeyer Flask, 250ml, Non-stick PFA Surface–easy to CleanUS$ 141 - 150MOQ: 3 Pieces
-
PFA High-purity Conical Flask Titration Reaction VesselUS$ 129 - 280MOQ: 3 Pieces
-
Teflon Erlenmeyer Flask PFA Triangular Flask With Threaded Mouth OR Insert Type PortUS$ 1 - 169MOQ: 1 Piece
-
Lab Equipment Graduated Erlenmeyer Flask Plastic Transparent PC PETG Triangular Conical Flask With Screw Cap for Laboratory UseUS$ 0.2 - 2MOQ: 10000 Pieces
-
Plastic TC Treated 25cm2 75cm2 175cm2 225cm2 Cell Culture Consumables FlaskUS$ 0.1 - 3MOQ: 1000 Pieces
