3528 SMD Led Strip Light Dripping Glue Waterproof(60 LED per Meter)
LED Strip PLCC SMD Type Mounted on Flexible PCB
Input Voltage: DC 12V/24V
Color temperature (nm)cold white7000K-7500K;white6000K-6500K warm white3000K-3500K
Luminance (mcd):red: 400-500 yellow: 400-500blue400-500 green: 1000-1300 white1600-1800
Waterproof Material: Silicone hollow tube
Color: cool white, pure white, warm white, red, yellow, blue, green, RGB
Optional: IP45/IP65/IP67/ IP68
LED CHIP: 3528 Made in Taiwan
60 LED Per 1 Meter Strip, Each Strip Connected in Series
With 3M adhensive tape backside for easy installation.
3 units LEDs cuttable for 12V 5/6 units LEDs cuttable for 24V;
Saving Energy Percentage: 88%
LED LIFE 30,000 ~ 50,000 Hours
View Angle: 120
Operating Temprature: - 30 Degree ~ + 50 Degree Celsius Max
Carbon Emission(hrs): 4.466g
Anti-oxidation, anti-UV radiation and wont change color after long time use.
High flexibility ,high transparence, flame-proof and environmental friendliness.
Silicone material offers good heat or cold resistance and is not easily broken.
With silicone transparence waterproof connector can easily connect and totally waterproof
1Solder connection should only be performed on designated solder pads(marked ). During soldering,dont exceed the maximum soldering time of 10 seconds and the maximum soldering temperature of 260 Celsius degrees.
2The smallest unit (3 LEDs) can be removed by cutting with scissors between the designated solder pads.
3The mounting of the strip is facilitated by means of the double-sided adhesive on the back-surface of the strip. Care must be take to provide a clean and dry mounting surface,free of oils or silicone coatingas well as dirt particle. The mounting substrate must have sufficient structural integrity. Take care to completely remove the adhesive backing. Oncethe stipis appropriately positioned. Press on strip with about 20N/cm2(refer to application techniques of 3M adhensive transfer tapes).
4The minimum bending radius is 2 cm. The strip may be bent over a smaller radius of the circuit board containing no electronic components and such bends should be made once and fixedin position to avoid cyclic fatigue.
5After cutting along the line, ifyou want to connect the cutting sections or connect one sectionto power, the connectors will be necessary
interior lighting
exhibit lighting
kitchen-cabinet lighting
Car decoration
Architectural decorative lighting
Archway,canopy and bridge edge lighting
Amusement park,theater and aircraft cabin mood lighting
VEmergency Hallway lighting
Auditorium walkway lighting
Emergency exit path lighting
Cove lighting
Border or perimeter lighting
1Please make LED drivers compatible with waterproof led strips light before use LED strips;
2To use waterpoof led strip light 5M in serial, longer than 5M in parallel;
3Before use,first check the power supply used in compliance with of the power requirements;
4Each roll ask for independent power supply;not to use of multi-volume series use;
Send Inquiry to This Supplier
You May Also Like
-
Slide SwitchNegotiableMOQ: 2600 Pieces
-
Mini Slide SwitchUS$ 0.01 - 0.05MOQ: 500 Pieces
-
KG-1005B Guitar Parts Toggle SwitchUS$ 2 - 3MOQ: 100 Pieces
-
3pin Differernt Height Slide SwitchUS$ 0.03 - 0.7MOQ: 500 Pieces
-
Electronic Switch Mini Slide Switch 2p2tUS$ 0.1 - 1MOQ: 100 Pieces
-
ALPS Toggle Switch SSSSSS811101 Side 7 Pin 2nd Gear Power Supply Device Audio Sliding SwitchUS$ 0.06 - 0.07MOQ: 4500 Pieces
-
Miniature Slide Switch 2P3T About 0.5A 50V DCUS$ 0.01 - 0.08MOQ: 1000 Pieces
-
6 Pin Mini Slide Switch MK-22D01US$ 0.1 - 2MOQ: 1 Piece
-
12.7*6.6mm SS-12D28 Handle Height 4mm High Current Side Plug Slide SwitchUS$ 0.433 - 0.5MOQ: 1000 Pieces
-
Small 0 - 10V / 0 - 5VDC, 100Hz Signal Conditioning, Converted and Isolation AmplifierNegotiableMOQ: 1 Piece