Contact Platform Support
Help CenterMiniature Above 420mm Size Standard P5 Precision Tapered Roller Ball Bearings 33020
Related Products
-
Sealed Single Row Tapered Roller Bearings 32948,32048,32048X2 ,32248 Cylindrical RollersNegotiableMOQ: 1 Piece -
Metric Four Row Custom Standard P6 Precision Tapered Roller Bearings Design 32221NegotiableMOQ: 1 Piece
-
Above 420mm Dimension Standard Precision Tapered Roller Ball Bearings 30220NegotiableMOQ: 1 Piece
-
30205 Radial and Axial Load Wheel Single Row Tapered Roller Bearings 25x52x16.25mmNegotiableMOQ: 1 Kilogram
-
Genuine NSK HR30310J Bearing Japan Made NSK Taper Roller Bearing With 50mm Bore SizeNegotiableMOQ: 1 Piece
Certification:ISO9001, ISO14001
Above 420mm Size Standard P5 Precision Tapered Roller Ball Bearings 33020
Precision Tapered Roller Bearings
WD tapered roller bearings are produced by WD in many designs and sizes to match their many uses.These can be grouped as follows
Cages
WD tapered roller bearings are fitted with one of the following cages.
-A pressed window-type steel cage, roller centred.
-An injection moulded window-type cage of glass fibre reinforced polyamide 6, 6, roler centred.
-A steel pin-type cage
Minimum load In order to provide satisfactory operation, tapered roller bearings, like all ball and roller bearings, must always be subjected to a given minimum load, particularly if they are to operate at high speeds or are subjected to high accelerations or rapid changes in the direction of load. Under such conditions, the inertia forces of the rollers and cage, and the friction in the lubricant, can have a detrimental influence on the rolling conditions in the bearing arrangement and may cause damaging sliding movements to occur between the rollers and raceways.
The requisite minimum radial load to be applied to standard tapered roller bearings can be estimated from
Frm = 0, 02 C Where
| Frm |
=
|
minimum radial load, kN |
| C |
=
|
basic dynamic load rating, kN (see product table) |
When starting up at low temperatures or when the lubricant is highly viscous, even greater minimum loads may be required. The weight of the components supported by the bearing, together with external forces, generally exceeds the requisite minimum load. If this is not the case, the single row tapered roller bearing must be subjected to an additional radial load, which can be achieved easily by applying preload. For additional information, refer to the section “Bearing preload”.
Equivalent dynamic bearing load
| P |
=
|
Fr | when Fa/Fr =re |
| P |
=
|
0, 4 Fr + Yfa | when Fa/Fr >re |
| The values of the calculation factors e and Y | |||
| can be found in the product tables. |
Equivalent static bearing load
| P0 = 0, 5Fr + Y0Fa |
| When P0 < Fr, P0 = Fr should be used. The value of the calculation factor Y0 can be found in the product table. |
Determination of axial load When a radial load is applied to a single row tapered roller bearing, the load is transmitted from one raceway to the other at an angle to the bearing axis and an internal axial force will be produced in the bearing. It must be considered when calculating the equivalent bearing loads for bearing arrangements consisting of two single bearings and/or bearing pairs arranged in tandem.
The necessary equations are provided in table 3 for the various bearing arrangements and load cases. The equations are only valid if the bearings are adjusted against each other to practically zero clearance, but without any preload. In the arrangements shown, bearing A is subjected to a radial load FrA and bearing B to radial load FrB. Values of the loads FrA and FrB are always considered positive even when they act in the direction opposite to that shown in the figures. The radial loads act at the pressure centres of the bearings (dimension a in the product table).
In addition to an external force Ka acts on the shaft (or on the housing). Cases 1c and 2c are also valid when Ka = 0. Values of the factor Y can be found in the product table.
WD Tapered Roller Bearings have tapered inner and outer ring racesways between which tapered rollers are arranged.Both of which have single and double row structures.With the higher precision than P5 standard, they have high dimension and running accurancy accordingly. Tapered roller bearings with high speed and long lifespan are always used in Automobile, Gearbox, Main shaft of machine tool, Construction machineries, Rolling mill equipment.
| Bearing Code | 33020 |
| d | 100 |
| D | 150 |
| B | 39 |
| C | 32.5 |
| T | 39 |
| R2smin | 2 |
| R4 |
Send Inquiry to This Supplier
You May Also Like
-
A4VG125 Backhole Loader Hydraulic Pump Parts, A4VG Piston Pump A4VG90 A4VG125 A4VG180 A4VG250 Hydraulic Spare Parts in StockNegotiableMOQ: 1 Set
-
Universal Skid Steer Loader Pickup Box Road SweeperUS$ 1350 - 1600MOQ: 1 Piece
-
Chromium Carbide Overlay Wear Plate Excavator Crusher Bucket LinerUS$ 399.69 - 399.69MOQ: 1 Square Meter
-
Supply Excavator Repair Seal Kit P01609000597NegotiableMOQ: 1 Fluid Ounce
-
Excavator Hydraulic Pump With SAE J744 Standard Compliant for Global CompatibilityNegotiableMOQ: 500 Pieces
-
For Volvo Penta Fuel Filter 20998367 (7420514654 – 20998367)NegotiableMOQ: 1 Piece
-
A10VO45/52 DFR DFLR Control Valve and Rotary Group, Axial Piston Variable Pump Spare Parts, A10VO Series 52 and 53 Series Hydraulic Piston Pump PartsNegotiableMOQ: 1 Set
-
Rexroth Hydraulic Spare Parts A7VO Series A7VO28 A7VO55 A7VO80 A7VO107 A7VO160 A7VO172 A7VO200 A7VO250 A7VO355 A7VO500 Hydraulic Pump PartsNegotiableMOQ: 1 Set
-
New High-Pressure Rotary Group REXROTH A10VO71 A10VSO71 A10VO74 A10VSO74 Diesel Hydraulic Parts Hydraulic Pump Parts Hydraulic Spare PartsUS$ 138.70MOQ: 1 Set
-
Original New Travel Motor Final Drive PHV-1B-12 PHV-1B-12B for U15 U17 Yanmar Vio15 E301.5 E301.7 ET17 ET16 IHI18NegotiableMOQ: 1 Piece
