Contact Platform Support
Help CenterAdjustable Arced Concrete Column Formwork With 18mm Plywood
Related Products
-
Adjustable Semi-diameter Arced Concrete Column Formwork for Curved WallNegotiableMOQ: 1 Piece -
Adjustable Square or Rectangle Concrete Column Formwork With Variational DimensionNegotiableMOQ: 1 Piece
-
Adjustable Concrete Column Formwork for Square or Rectangle With Vertical Waling EtcNegotiableMOQ: 1 Unit
-
Adjustable Square or Rectangle Concrete Column Formwork With Plywood, Timber Beam EtcNegotiableMOQ: 1 Piece
-
High Standard Adjustable Semi-diameter Arced Concrete Column FormworkNegotiableMOQ: 1 Piece
Certification:ISO9001-2008
Adjustable Arced Concrete Column Formwork with 18mm Plywood
Descrition:
It can be used for any curved wall with the semi-diameter longer than 1.10m
Adjustable acted Formwork Profile
Adjustable Semi-diameter Arced Formwork On the basis of the foreign company technology, we developed the
Adjustable Semi-diameter Arced Formwork, which can be used for any curved wall with the semi-diameter
longer than 1.10m. Traditionally, the formwork is produced in accordance with the designed semi-diameter,
which is one-off use, causing much material wasting. All the defects of the traditional formworks are overcome
after we developed the Adjustable semi-diameter arced formwork. Also, we lease the formwork out to the contractors
to save their cost, which proves good effect.
Adjustable acted Formwork\'s panel is 18mm Plywood,because the panel specification is 2440×1220 mm,so the formwork
max width is 2440mmUpright rib is combination steel frame ,the panel and the steel frame is connected by bolt ;
Horizontal rib is short Double-side V-iron , there are adjustable connectors between V-iron.Upright side-rit is angle steel .
The radius can be regulated at any time when meet to different section. Adjustable Acted Formwork Technique parameter:
Allowed Load50-70KN/M2 Per square meter65KG
Advantage of the product
Can be adjusted to any curved wall with a semi-diameter longer than 1.1m
Easy and quick operation.
Low cost and wide use.
High standard elements.
Assembly procedure
1. Assemble timber beam and timber connector.
2. Assemble plywood and edge rib.
3. Assemble adjustable system.
4. Assemble connecting waling.
5. Adjust the formwork, make the formwork bent into designed radius.
6. Connect every module by adjustable steel clamp.
One plan sketch is shown below
Send Inquiry to This Supplier
You May Also Like
-
Large Glass Windows Wall SystemUS$ 180 - 500MOQ: 50 Square Meters
-
Elengant Toughened Double Glass Sliding DoorUS$ 100 - 800MOQ: 10 Pieces
-
Chinese Antique Red Wooden Folding DoorsUS$ 380 - 450MOQ: 1 Piece
-
Quick Open and Close Wheel Handle Ship Steel DoorUS$ 400 - 600MOQ: 10 Pieces
-
High Quality Well Design Sliding Door Fitting/Glass Shower Doors Fittings/Sliding Door AccessoriesUS$ 1 - 45MOQ: 1 Unit
-
Clean Room Powder Coated Steel DoorUS$ 1 - 1MOQ: 1 Unit
-
3.0mm Decorative Interior HDF Melamine Door Skin /Natural Ash HDF Veneer Door Skin/teak Veneer HDF Door SkinUS$ 5 - 15MOQ: 5000 Pieces
-
Door HardwareNegotiableMOQ: 1000 Square Meters
-
Durable Lightweight Suspended Platform Cradle Construction Gondola ZLP800 ZLP1000NegotiableMOQ: 1 Square Meter
-
Self Adhesive Printed Foil(Indoor Decoration)NegotiableMOQ: 1
