Contact Platform Support
Help CenterPOE Switch
Related Products
1. Introduction:
Optostar's /106/108-24V Series Injector inserts current into the unused wires in a standard network cable (pin: 4, 5, 7, 8)to allow the cable betweenPSE104-24V Injector andPSE104-24VS Splitter to transfer power and network signals simultaneously. When positioning network devices, system designers always have to consider the location of power outlets. In some cases, this will restrict the optimum placement of devices or incur additional cost in installing new outlets. OPTOSTAR's PSE104-24V/POE101 offer the solution of these problems. Using the Optostar PSE104-24V/POE101 adapters, you can power most DC network devices (hubs, Wireless access points, cameras etc) over the same Cat 5/5e cable used to connect the device to the network.
2. Features:
* Provides 24V low-voltage DC power over existing Category 5 cabling to a device with an Ethernet port Distance up to 100 meters
*Protects devices from possible damages due to power-surges
*Threedifferent output voltage options (5V/2A, 9V/1.2A, 12V/1A) to fit various devices
* Work with EIA568, category 6, 5-pair cable for 10Base-T or 100Base-TX, Ethernet / Fast Ethernet network.
Please note:
1. PSE104-24V/POE101 does not comply with IEEE802.3af, Don connect any of it to an IEEE802.3af devices.
2. For PSE104-24V, it will inject power all the time when it is connected with a AC/DC 24V adaptor. It means that (pin: 4, 5, 7, 8) inject power all the time, so when you connect it into network, please make sure the safety of body and connected equipment.
3. PSE104-24VS is not an IEEE802.3af complied device, PSE104-24VS will not detect and reply the signal from 802.3af injector. As a result, the Power LED will never turns on if you connect to an IEEE802.3af injector and never power the remote device as well.
4. Gigabit Ethernet is not allowed to usePSE104-24V/POE101 products since pair 4, 5 and pair 7, 8 are all being used. Only 10/100M TX can apply with ourPSE104-24V/POE101.
5. For safety reason, PSE104-24V/POE101 will only support device with power consumption below 12watts. Please make sure the remote Ethernet device is under the range of 12V/1A, 9V/1.2A, 5V/2A.
6. Please by usingPSE104-24V/POE101 together on both sides of cable all the time.
3. Application:
OPTOSTAR PoE Save Your Power Infrastructure Cost.
PoE allows power to be supplied to end devices, such as Wireless Access Points or VoIP Phones, directly through the existing LAN cables. By supplying the power end-span, you can centralize power distribution and backup without the need to increase infrastructure
Send Inquiry to This Supplier
You May Also Like
-
Honeywell SZL-WL-A Limit SwitchesNegotiableMOQ: 1 Piece -
HH 18HA416 Furnace Thermostat Limit Switch for CarrierNegotiableMOQ: 1
-
KW1-2 Limit Switch With WheelUS$ 0.45 - 0.8MOQ: 100 Pieces
-
Magnetic Window Contact SwitchUS$ 4 - 8.1MOQ: 20 Sets
-
Limiting SwitchesNegotiableMOQ: 1 Piece
-
Booking Queuing Ticket Vending Kiosk With Finger Print ReaderNegotiableMOQ: 1 Piece
-
-100-20000Kpa 5V Economical Specialized Electronic Pressure TransmitterNegotiableMOQ: 1 Piece
-
Service Resetting 10 IN 1 SERVICE RESETNegotiableMOQ: 1 Piece
-
Sell Micro SwitchNegotiableMOQ: 1 Piece
-
MAYRNegotiableMOQ: 1 Piece
