Factory directly sale briquette machine from agricultural waste

Factory directly sale briquette machine from agricultural waste

Introduction of fuel straw briquette making machine briquettes:

1. What's straw briquette charocal?

Fuel straw briquette making machine briquettes is to use rural corn stalk, what straw, cotton stalk, rice straw, rice husk, peanut shell, corn cob, tree branches, leaves, sawdust, etc, agricultural waste, solid waste as raw material, after crushing, be compressed into high density and strength of briquettes.

2. Features of "fuel straw briquette making machine briquettes".

The fuel straw briquette making machine briquettes with small volume, relative density, flame resistant, easy for storage and transport. The briquette volume is only 30% of the original straw; the weight is 10-15 times of the same size of the straw; the density is 0.9-1.4g/cm3; the calorific value can reach to 3500-5500 kilocalorie, is high volatile solid fuel.

3. The applied range of fuel straw briquette making machine briquettes:

The fuel straw briquette making machine briquettes can stead the wood, coal, liquefied gas etc, widely used in life stoves, heating stove, industrial boilers, biomass power plant, etc.

Fuel straw briquette making machine briquettes:

Burning conditions of fuel straw briquette making machine briquettes:

The performance of fuel straw briquette making machine:

1. High capacity, low price, low power consumption: 1.5-2.8 tons per hour, small power consumption.

2. Material strong adaptable: suitable for all kinds of biological material moilding, straw from powder to 50mm length, the moisture content is between 5-30%, can all be pressed into briquettes.

3. Electric heating function: automatic electrical heating device can adjust the humidity of material, solve the problems of congestion and briquetting.

4. The adjustment function of rollers: by using the principle of bi-directional thrust bearing rotation automatically adjust the pressure Angle, the wet material is not crowded, not boring maching, keep stable discharging molding.

5. The operation is simple, easy to use: high degree of automation, less labor, needs only three people, artificial feeding or automatic screw conveyor feeding.

6. Technological process: Crushing--Conveying--Briquetting--Products in store.

The operation principle:

1. Before starting: please firstly pure 25 kg gear oil, tighten the plug head fillingafter refueling.

2. Carefully check the power line, prevent the electric leakage and ensuring the safty of using electricity.

3. Carefully check the machine motor, transmission parts in parts of bolts, screws are solid, if there are any loose phenomenon, in order to timely fastening.

4. Fuel straw briquette making machine briquettes for material requirements: the length should be less than 60mm corn straw,wheat straw which the water content should be 10-20%; the peanut shell,rice husk, which water content less than 12-14%.

5. Depending on the type of material before feeding set preheating temperature, corn and wheat straw between 70-90 degrees Celsius, peanut shell, rice husk between 80-100 degrees Celsius.

6. Idle for 1 minute before start up, check whether the machine rotation is normal, if normal, please firstly feeding for a little, after the remaining material is completely discharged out off the machine, then you can evenly feed material.

7. Before loading, please be sure to pay attention to the raw material of hard staff, put an end to stone and iron into the hopper so as not to damage the machine.

8. Every tine when run 8 hours, pure 2-3 drops of oil at a time. Please put a little wet material before downtime, so that the boot after discharge smoothly.

The matters needing attention:

1. When operating, please strictly in accordance with the operational procedures and operations.

2. When operation, can not touch the hot parts, so as to avoid the burns.

3. Material is too wet, can't start the machines.

4. No material, do not idle in the hopper. If raw material moisture content over 30% boring machine (discharging) occur, shut off the machine in time and clean up the wet material inside the hopper, then added to confirm to the requirements of the raw material can be normal production.

5. If the machine has abnormal noise, stop the machine immediately, to mcheck it, it is forbidden to remove the hopper boot.

Flat die fuel straw briquette machine:

Technical parameters of fuel straw briquette making machine:

Assist equipments of making straw fuel briquettes:

Besides the fuel straw briquette making machine, we have also some other assistant machines for making straw briquettes, like crusher, powdery delivery machine, cotton straw harvest machines, etc, please have a check of the following pictures:

Straw crusher 1:

Straw crusher 2:

Packaging & Shipping

Packaging and shapping of our machines:

 

1. Payment: 30% down payment by TT in advance, or pay directly by Crush, 70% TT balance pay off before delivery.

 2. Packaging:

1). All the machines will be wrapped up with plastic film firstly (including the motors)

2). The plastic film bag wrapped machine, according to the size and weight to make wooden or iron box, put machine in and fixed the box after loading. (The box material can be made as your requirements)
3). The machine parts need to be put in a fixed container, should be fixed well, lest collision and wear, or lost.

3. Delivery: after receive your down payment, we will prepare and manufacture all the machines for you, within 15-20 days, all will be finiahsed, we will send pictures to show you, after receive your balance, all the machines will be loaded on board and delivered to you.