Control 300M Lithium Battery Dog Bark Training Collar With Static / Beep

Product Application

CENTRALIZED CONTROL SYSTEM, FIX EVERYTHING WITH ONE "MOED"

The PET-916 E-collar is designed with basic pet dog training functions: beep, vibration, static shock. What makes it different is it's One-Stop training system. You don't need to remember the buttons with their different functions, you may press " the other buttons " by mistake. For PET-916, you just need to press the " Mode " to choose the training method you want, and press " Y " for final confirmation. In this way, you can get your dog well-trained effectively.

100 INTENSITY TRAINING LEVELS WITH NO JUMP

The PET-916 is an E-collar with wide stimulation range for vibration and static shock, you can choose the proper levels depending on how your dog reacts while training, it goes well with a large range of dogs with different sizes. The No Jump design can protect the dog from sudden increase in intensity. make the training experience safe and enjoyable.

TRAIN TWO DOGS AT A TIME

The PET-916 Remote Dog Training E-collar can be extended up to 2 dogs, which means, you just need an extra dog collar, you can get 2 dogs well trained with one dog training system. There is a button for your to select which dog should be trained duo to it's imporper manner.

SAME TIME CHARGING FOR TRANSMITTER AND RECEIVER

No need to go through stores for batteries to fit in the articles, you can get the transmitter and receiver charged at the same time with one charger, easy and effective ! The whole set is matched with lithium Battery with good quality.

Test the training system

The following testing methods will help you ascertain whether this training system functions swimmingly. Please make sure that you have connected the transmitter and collar-receiver before testing.

Test static shock function:
Put the test-light on the contact points of the collar-receiver. Turn on the remote transmitter, switch to SHOCK mode and press the UP/DOWN button to adjust the intensity level. Press “Y” button and the bulb will flash, signifying that the SHOCK function works. Please make sure the SHOCK level is above 0 when testing the function.

Test the vibration functions
Turn on the remote transmitter, switch to VIBRATION mode and press the UP/DOWM button to adjust the vibration level.Press “Y” button and the collar-receiver will vibration, signifying the VIBRATION function works. Please make sure the vibration level is well above 0 when test the function.

Test the beep function
Turn on the remote transmitter, switch to BEEP mode. Press “Y” button, the collar-receiver will beep, signifying the BEEP function works.

Charge the remote transmitter:

1. Connect the charger connector to the charging hole.
2. Plug the charger into a standard outlet.
3. The red light in the transmitter will be on, indicating that
charging is taking place.
4. Charge the transmitter at least 6 hours for first charge or until indication that charging is complete.
5. When charging is complete, the red light will turn off automatically.
6. Low Battery Indicator “Battery ” signals the need for recharging.

How to use the remote transmitter

1.To turn on/off the transmitter, press any button on the transmitter.
2.Press the MODE button to toggle among 4 different modes.
3. Press IP/DOWN buttons on the lights hand side of the transmitter to adjust the intensity level of vibration or static shock.
4. “1/2” button indicates either channel 1 or channel 2 on the transmitter. Select one channel for use with one collar-receiver.
5. The remote transmitter will go into STANDBY MODE if no operation for 2 minutes and will turn off if no operation for 5 minutes.
6. In STANDBY MODE, press any button to wake it up. When turned off, press and hold the MODE button for 1 second to turn on the transmitter.

Sync transmitter with collar-receiver:

1. Turn on the remote transmitter by pressing any button on the transmitter.
2. Select channel 1 or 2.
3. Press ON/OFF button on the collar-receiver to turn it on.
4. Press ON/OFF button afresh and hold it for 5 seconds, and then the LED light will start to flash.
5. Now you can hear the first beep from the collar-receiver and then press the “Y” button (of the transmitter) immediately.
6. You will hear the second beep from the receiver, which signifies that the transmitter and the receiver have been synced.
7. To sync the transmitter and the second receiver, repeat step 2 through 6.
8. Please be sure to choose the other channel.