Contact Platform Support
Help CenterEPDM Rubber Roof Membrane
Related Products
-
Pvc Waterproofing MembraneUS$ 2.2 - 3.65MOQ: 2050 Square Meters -
EPDM Rubber Waterproofing MembraneUS$ 2.25 - 3.7MOQ: 1000 Square Meters
-
PVC Waterproof MembraneUS$ 2.2 - 3.65MOQ: 2050 Square Meters
-
PVC Waterproof MembraneUS$ 2.2 - 3.65MOQ: 2050 Square Meters
-
Pvc Membrane SheetUS$ 2.2 - 3.65MOQ: 2050 Square Meters
Epdm Rubber Roof in Rolls Membrane
Characteristics:
Good synthesis aging resistance;ozone resistacne;ultravoilet resistance;chemical resistance;corrosion resistance.High tensile strength and good elasticity;endured the puncture-resistant and cracking resistance.
Specification:
With: 1m;
Length: 20m
Thickness:1.2mm;1.5mm;2mm
Packing:
Technical data for EPDM Membrane:
Technical Capacity Index(Ref to Chinese Standard GB18173.1-2006) | ||
EPDM Rubber Waterproof Membrane | ||
No. |
Item |
Index |
|
1
|
Water tightness |
≥0.3 Mpa,No leakage
|
2 |
Tensile strength |
≥7.5Mpa |
3 |
Elongation at break% |
≥450 |
4 |
Tearing strength,KG/m |
≥25 |
5 |
Brittleness point |
≤-40 |
Application
Widely used in roofs, basement, toilet ,swimming pool, and all kinds of industry and civil building waterproofing, reservoir, vivicism, bridge, underground, tunnel and dam waterproofing ,especially to the keystone waterproofing projects which is durability, high corrosion resistance and easy deformation
Application Method:
1. Make sure the roof deck smooth,clean and dry(Moisture<9%),then apply the surface of roof deck homogeneously with a kind bitumen paint till dry to start application.
2. There are two methods in application:
One way is by heating and melting method---Heat the polyethylene film of the membrane and roof deck surface by heating and melting method to be nearly melted(not flowing),then install the membrane fully bonded to the roof deck with overlaps of 5-10cm.
The other way is by cold adhesive method---Pour the cold adhesive homogeneously on the roof deck then roll the membrane to install it to be fully sticked to roof deck.
By heating and melting method and by cold adhesive can be used in alternation in application as requested.
3. After application,a full serious inspection is required to make sure no air bubble,no fold,no falling away etc to guarantee the waterproof life.
Attentions for Construction:
Construction shall not be carried out in rain, snow or over 5 degree wind weather; There shall be sufficient safety protective facilities in construction site, place firefighting devices according to stipulations
1. Clean the substrate using broom or high pressure dusty cleaner
2. Apply primer
3. Heat the membrane bottom using a high temperature flame gun
4. Push forward while the primer and membrane oil melted
5. Use a roller to push hard the membrane surface to ensure it stick firmly
Send Inquiry to This Supplier
You May Also Like
-
High Adhesive, Water-proof, Anti Corrosion, Weather-resistant Asphalt Adhesive Glue Patch Cover for ConstructionNegotiableMOQ: 100 Rolls
-
2.0mm Textured HDPE Geomembrane Dual-Sided Friction for Slope ProtectionUS$ 9.5 - 10MOQ: 100 Square Meters
-
GeomembraneNegotiableMOQ: 2700 Rolls
-
Non-curable Rubber Paint Rubber Asphalt Waterproof Coating Made in ChinaUS$ 1.5 - 6MOQ: 500 Kilograms
-
Low Cost Waterproof Material ManufactureUS$ 1,000 - 50,000MOQ: 1 Set
-
PTFE Architectural Membrane MaterialNegotiableMOQ: 1
-
Special Compound BaseUS$ 0.12 - 0.25MOQ: 7000 Square Meters
-
PolyLock/HDPE Lock/ E Lock/ HDPE E Lock/Geomembrane Attaches HDPE GeomembranesUS$ 10 - 50MOQ: 1 Piece
-
Breathable House Wrap Membrane Roofing Waterproofing MembraneUS$ 0.42 - 0.42MOQ: 5000 Square Meters
-
<MIicroVENT> Waterproof Vent MembraneUS$ 0.1 - 3MOQ: 10000 Pieces
