Contact Platform Support
Help Center50kA 10/350us CLASS I Wind Power Generation SPD
Related Products
-
50kA 10/350us CLASS I Wind Power Generation Lightning Protection DeviceUS$ 380 - 480MOQ: 1 Set -
50kA 10/350us CLASS I Wind Power Generation AC Surge ProtectorUS$ 400 - 500MOQ: 1 Set
-
50kA 10/350us CLASS I Wind Power Generation 440V Surge ProtectorUS$ 390 - 490MOQ: 1 Set
-
50kA 10/350us CLASS I Wind Power Generation Lightning ArresterUS$ 400 - 500MOQ: 1 Set
-
50kA 10/350us CLASS I Wind Power Generation Under Voltage ProtectorUS$ 400 - 500MOQ: 1 Set
1. APPLICATION
Huge energy released by the lightning would cause the wind turbine blades damaged, insulation breakdown, control components overburdened, etc. Therefore wind power SPD has became one of the powerful guarantees for safe and normal operation of the wind turbine.
It is mainly applicable for the electronic and power supply devices lightning protection and under voltage protection in the fields of telecommunication, railway, internet, power supply, traffic and house, etc.
2.TECHNICAL PARAMETERS
Model DXH06- |
FWB/2 |
FWB/3 |
FWB/4 |
FWB/3+1 |
Type IEC 61643-1 |
Class I/Type 1 |
|||
Max. Continuous Operating Voltage(Uc) |
440VAC |
760 VAC |
||
Applicable Power Supply |
Three Phase |
|||
Discharge Current Capacity |
50kA(10/350μs) |
|||
Protection Mode |
L~PE |
|||
Protection Level(Up) |
≤2.5kv |
|||
Follow Current Extinguishing Capacity |
3kA |
|||
Response Time(T) |
<100ns |
|||
Live Line(mm² ) |
≥10 |
|||
Earth line(mm² ) |
≥16 |
|||
Grounding Resistance(R) |
≤4Ω |
|||
Protection Level of the Shell |
IP20 |
|||
Operating Temperature |
-40℃~+70℃ |
|||
Overall Size(mm) |
150×77×36 |
150×77×72 |
150×77×144 |
|
Installation Method |
35 mm DIN-rail |
|||
3. Wiring Diagram
4. Main Characteristics:
l Excellent varistor, with reliable quality;
l Quicker response time;
l Big discharge capacity;
l Low residual voltage.
5. Installation Method and Attentions
1) Wiring as shown in Figure;
2) The connecting lead shall use many strands of copper wires of more than 6mm2, and the earth wire shall use many strands of copper wires of more than 10mm2. The connecting wire shall be as short, straight and coarse as possible. Grounding Resistance should be no less than 4Ω;
3) The front of lightning arrester shall be connected with proper fuse in series or be opened;
4) The power supply must be cut off while conducting the installation. It is prohibited to conduct the operation with the charge. The connecting lead must conform to the requirement;
5) After completing the installation, the lightning protection module shall be inserted tightly and inspected;
6) When there is RED for the fault indicator of the lightning arrester module (warning signal of remote-signaling port), it indicates that the lightning protection module has degraded and shall be replaced;
7) The SPD needn't special maintenance, but only check the connection and indicating state periodically.
6. Certificates:
Send Inquiry to This Supplier
You May Also Like
-
DANFOSS Controller MCX08M080G0310NegotiableMOQ: 1 Piece
-
Steelmaking Arc Furnace TransformerNegotiableMOQ: 50 Sets
-
CEEG China Hermetically Sealed Oil Transformer - Weatherproof, Corrosion Resistant Tank, Low Maintenance, for Outdoor InstallationNegotiableMOQ: 1 Unit
-
Toroidal Transformer for Cable Pusher, Cable Conveyor, Cable Puller Machine – Professional Industrial Power Supply ComponenUS$ 100 - 200MOQ: 1 Unit
-
Power TransformerNegotiableMOQ: 2000 Pieces
-
WOODWARD 8901-457 – Industrial Control Module for Engine/Turbine Protection and Speed ManagementNegotiableMOQ: 1 Bag
-
Motorola MVME167-34B VME Bus Single-board ComputerNegotiableMOQ: 1 Piece
-
Yaskawa JEPMC-MP2300S-E Machine Controller MP2300NegotiableMOQ: 1
-
Wholesale High Quality New Surge Arrestor (SP-D10)US$ 0.01 - 0.02MOQ: 1 Piece
-
High Precision Mini Coil Inductor GEM005US$ 0.5 - 0.8MOQ: 1000 Pieces
