Lycos Sanitary Ware Accessories Urinal Pan Exp-lycos-s59

Name: Lycos Sanitary Ware Accessories Urinal Pan Exp-lycos-s59
Brand: LYCOS CERAMIC
Availability: InStock

FOB Price

US$ 5 - 50 / Piece

500 Pieces(Min. Order)

Port mundra/kandla
Payment TermsT/T L/C Credit Card PayPal

Request Sample Customized Request Request Free Catalogs

Contact Now

Get lowest price

Product Details

Place of Origin	Gujarat, India	Brand Name	LYCOS CERAMIC
Model Number	lycos exp-s59	Material	Ceramic
Component	Toilets, Other, Toilets, wash basin

Product Description

Specifications

Leading Exporters of Bathoom Sanitary Ware
Brand " LYCOS"
Wide Range & Best Quality
Attractive Price
Timely Delivery

Technical Specifications

Specifications of 'LYCOS SANITARY WARE' Products

Charactristics	IS 2556-1-1994	LYCOS' Test Value
Surface Blemish	Should conform to Norms	In conformity with the Norms
Water Absorption %	0.5 Max. Mean Value	0.1 Max. Mean Value
Modulus of rupture (M.O.R.)	60 Mpa Min. Mean Value	70 Mpa Min. Mean Value
Crazing Resistance 0.34- 0.37 Mpa	10 Hrs. Min.	20 Hrs. Min.
Chemical Resistance	Should Conform to Norms	In Conformity with the Norms
Staining & Burning Resistance	Should Conform to Norms	In Conformity with the Norms

INSTALLATION & MAINTENANCE TIPS

Install Wash Basins with or without pedestals on CI Bracket with Rag Bolts. If wash basin is Large in size install on pedestal screwed to the floor.

Install wall mounting E.W.C. With the help of CI chair.
Install Floor Mounting E.W.C. Screwed to the floor.
Avoid using Cement at the hollow bottom portion of E.W.C.
Regular Cleaning with dry cloth / Mild Detergent is recommended to avoid stains & if required diluted Hydrochloric acid may be Used.
Do not use hard bristled brush for cleaning so as to avoid scratches.

Your Trouble-Shooting Guide

(FOR GOLD - TYPE FITTINGS)

At Ceramics Division, LYCOS Ceramics, it has been our endeavour not only to provide you with the best possible service, but also to help you serve your customers better. We have been analysing the complaints received by us and have discovered that most of the complaints fall into a pattern. We would like to share the qualitative results of the analysis with you, so that you can be better prepared to handle any complaints received from your customers.

For each problem faced, the probable causes are explained. Alongside, you can find the corrective actions required to solve these problems. We hope that you would find this trouble-shooting chart useful. You could apply this for suites as well as wallvit pans

Flushing Test

1 Toilet Paper Test

The water closet shall be filled with water to its normal water seal level and charged with six pieces of usual toilet paper or polythene sheet of 0.05 mm thickness approximately 150 mm x 115 mm in size and loosely crumpled. It shall then be flushed. This test shall be repeated four times and the pan shall discharge the full charge of the paper at last three out of four times.

2 Smudge Test

The whole of the interior surface of water closet to 40 mm below the flushing rim shall be smudged with quartz powder of contrasting colour passing through 1.18 mm IS sieve and shall then be flushed observing carefully the surface of the water closet during the flushing. Immediately after the flushing, there shall be no smudge left on the bowl.

3 Holding Capacity Test

The water closet when sealed at the outlet and vent (if fitted) with water-tight seal shall be capable of holding not less than 10 1 of water between the normal water level and the highest possible water level of the water closet as installed.

4 Ball Test

Single Ball Test :The ball shall be made of non-absorbent material. The relative density of the ball shall be between 1.075 and 1.080. The diameter of the ball shall be 43 ± 0.5 mm. Place the ball into the water closet to be tested and then flush the water closet. The ball shall be discharged in the normal manner.

The outlet (trap) of the water closet goes into the floor.

The outlet (trap) of the water closet goes into the wall.

5 Fifty Ball Test

Fifty balls of non-absorbent material, having a mass each of 3.7 ± 0.1 g, and a diameter of 20 ± 0.1 mm
shall be dropped into the water closet bowl and flushed. Repeat the test five times. A minimum of 85
percent of all balls should be flushed out in the five tests.

6 Load Bearing Test

force of 4 + ° .05 kN shall be applied for period of one hour by placing it on a wooden beam with a cross
section of 100 mm x 100 mm positioned across the centre of the opening of the top surface of the WC.
There shall be no damage or defect which shall occur to the WC.

7 Saw Dust Test

Specification of the Saw Dust 20 g of dry saw dust test sifted through 2 mm sieve.
Procedure: Set up the WC, cistern or flush valve and flush pipe (if required) as specified by the
manufacturer. Charge the WC with water to its designed water seal level. Fully wet the entire internal
surface of the WC below the rim. Sprinkle 20 g of fine dry saw dust of above specification on the inside of
the WC between the normal water level and the flushing rim as completely and evenly as possible. Then
flush the WC. The sprinkle saw dust should be cleaned below 40 mm of rim of WC.

8 Splash Test

Procedure: Set up the WC, cistern or flush valve and flush pipe (if required) as specified by the
manufacturer. Charge the WC with coloured water to its design water seal level. Ensure that the floor area
is cleaned and dry where the splash test to be carried out. Activate the flush valve or cistern to the
discharge the WC. Observe and record whether flushing water splashed over rim onto the floor. Repeat
the test 5 times. Record whether the flushing water splash over the rim onto the floor. Isolated droplets up
to 10 Nos., shall not be the cause for rejection.

Problem faced	Probable Reasons	Corrective Action
Tank is shaking	Expansion plug may not be correctly fixed in the tank's fixing hole provided towards the back of the closet.	Fix the expansion plug provided.
Tank is shaking	Tank holding screw may not be tightened fully.	Tighten the tank holding screw evenly till it cannot be tightened any further with one hand.
Continuous leakage of water from the cistern	Arm may be fixed in a wrong direction.	Fix the arm such that the shorter arm side is facing the front of the cistern.
	Valve ring may not be fixed properly to the bottom of the body.	Fix the valve ring to the top of the groove provided in the body. Ensure that the valve ring sits securely around the groove.
	Valve ring may have cracked or could be worn out.	Replace the valve ring.
	Lifting rod and floating body assembly may not be perpendicular.	Adjust the bracket so that its center hole aligns with the hole provided in the lid of the cistern.
	Lifting rod and floating body assembly may not be guided through the guide hole provided in the bottom of the valve seat.	Guide the lifting rod through the hole provided in the bottom of the valve seat.
	Cistern not fully tightened to the closet.	Tighten tank holding screws evenly till they cannot be tightened further with one hand.
Discharge of water stops abruptly when the flush knob is pulled and released	Water may be overflowing through the floating body.	Turn the adjusting screw provided on the top of the inlet in the anti clockwise direction. Reduce the water level such that the water level shuts off below the 'over-flow' level.
	Buoyancy may not be created for the floating body.	1. Push stop dog (black rubber tube) which is fixed to the lifting rod such that top end of the stop dog touches the bottom of the lifting bar.
		2. Adjust the lifting bar such that the hole provided near the top-end threaded portion of the lifting-bar is just visible over the lid screw (when observed in assembled condition).
Water does not enter the cistern through the inlet	The inlet may be in the fully closed position.	Turn the adjusting screw provided on the top of the inlet in the clockwise direction to open the inlet.
Water does not enter the cistern through the inlet	Water line may be choked.	Ensure periodical cleaning of water tank and water lines.
Water quantity insufficient for effective flushing	Float ball height adjusted to lower quantity of water discharge.	Turn the adjusting screw provided on the top of the inlet in clock wise direction to increase the discharge level. (Caution: The water level may be increased till the water from the inlet shuts off at the 'top-line' mark provided on the floating body).
Water leakage observed between cistern and closet during flushing.	Water divider may not be properly fixed.	Fix the water divider such that the 2 weep holes provided in it face each other after installation. Ensure that the inlet of the water divider is passing through the outlet of the valve-seat fully

Continuous innovation and improvement in manufacturing techniques and products are carried out regularly. We reserve the right to supply articles which may not correspond exactly with the particulars given in this booklet.

Packaging & Shipping

Packed in 5 Layer Export Quality Corugated Box

Our Services

Quick and Efficient reply within 24 hours After receiving contact.
We accept OEM/ODM service.
Sample order will be available.
Confidentiality: Business between us will be confidential to any third party
Over 10 Years experience in manufacturing one piece toilet, two piece toilet, pedestal basin, urinal, counter basin, wall-hung basin,bidet and bathroom accessories and so on.
Service Parts available
Offices available in India, Nepal, China, Hongkong, Thailand, UAE and Singapore